Jump to content
Cura Connect | Survey Read more... ×
Ultimaker Community of 3D Printing Experts
Jlarson

Remote start

Recommended Posts

I have purchased the Ultimaker 3 and really like the network capability. I would like to be able to remote start the machine without being next to machine. I can dump program from Cura, but when I select the UM3 it asks me to allow access to the machine. Is there anyway to turn this off so I can print directly to the machine without an "allow" to be pressed on machine first? I can see the machine in the camera and know it is clear. I setup the machine before I leave for the day (along with other machines) and would like to remote start when jobs come in last afternoon or after hours. I can remote into my computer and start other machines and would like same access to Ultimaker. I can also get text messages or e-mail when jobs are complete from the Stratasys machine. Are these options in the future?

Share this post


Link to post
Share on other sites

You should only need to confirm on the printer once for every computer/cura combination. If you need to do it every time, something is wrong.

I'm sure such notifications are planned, and more.

Share this post


Link to post
Share on other sites

You should only need to confirm on the printer once for every computer/cura combination.

 

Not quite true at this moment: I agree that I don't have to go the machine and allow access to my Mac every time I start Cura, but every now and again I have to grant access to my (same) Mac again. Don't know why, not a big nuisance, but indeed it would be convenient if the UM3 permanently remembered that access was granted. Small bug perhaps?

Edited by Guest

Share this post


Link to post
Share on other sites

 

You should only need to confirm on the printer once for every computer/cura combination.

 

Not quite true at this moment: I agree that I don't have to go the machine and allow access to my Mac every time I start Cura, but every now and again I have to grant access to my (same) Mac again. Don't know why, not a big nuisance, but indeed it would be convenient if the UM3 permanently remembered that access was granted. Small bug perhaps?

 

It should do this. If it forgets it, it might be a bug (either on the printers side or on the side of Cura)

Share this post


Link to post
Share on other sites

I currently have 3 UM's (2 - UM2+'s and the 1- UM3) running thru CURA. The 2+'s run on the SD card and the 3 is hooked up thru LAN. I switch settings depending on the machine I am using. I am the only one with access to my machines and they are clear. I remote into my system, build / slice the job or part and send to the machine. I have cameras within my office to verify everything is good to go and would really like to turn the "access" request off or ON permanently. Seems like this should be a simple code switch. Would be great if I could select the access form the computer sending it.

Does Cura need to remain open to maintain the access? Or once Cura is closed does that reset the access?

 

 

 

You should only need to confirm on the printer once for every computer/cura combination.

 

Not quite true at this moment: I agree that I don't have to go the machine and allow access to my Mac every time I start Cura, but every now and again I have to grant access to my (same) Mac again. Don't know why, not a big nuisance, but indeed it would be convenient if the UM3 permanently remembered that access was granted. Small bug perhaps?

 

It should do this. If it forgets it, it might be a bug (either on the printers side or on the side of Cura)

 

Share this post


Link to post
Share on other sites

Does Cura need to remain open to maintain the access? Or once Cura is closed does that reset the access?  

 

No. Cura saves the access with a machine added to Cura. So if you have 3 machines, Cura should also have 3 machines added. Each of those (virtual) machines in Cura can then be linked to a physical machine.

Share this post


Link to post
Share on other sites

The UM2's are not physically connected to computer. I save to SD card for them. Cura does have all three machines loaded into "machines" and I select whichever one I am using. The UM 3 is connected via LAN / network but still asks "allow user" on machine every time I try to print. Evidently, the connection access is getting lost. (Have not shut machine off since it has started running jobs.) Does a great job of printing! I remote in to my computer a lot and would like to start the UM3 when I am not physically on site. I leave machine cleaned and ready to start before I leave for the day.

Is there a setting in Cura that my be off? Something I missed on setup?

 

 

Does Cura need to remain open to maintain the access? Or once Cura is closed does that reset the access?  

 

No. Cura saves the access with a machine added to Cura. So if you have 3 machines, Cura should also have 3 machines added. Each of those (virtual) machines in Cura can then be linked to a physical machine.

 

Share this post


Link to post
Share on other sites

Is there a setting in Cura that my be off? Something I missed on setup?

 

Nothing I can think off. I've been using the same authentication for some time now. Both Cura and the machine closed a number of times since first authenticating it (which is also how it's intended to work)

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Our picks

    • Architect Design Contest | People
      The goal of this contest is to design a set of people figurines that could be used in such a project to make an area, office or mall seem populated. 
      Think of different types of people in different environments, like walking people, people standing still, working people, and both men and women.
       
      • 8 replies
    • Taking Advantage of DfAM
      This is a statement that’s often made about AM/3DP. I'll focus on the way DfAM can take advantage of some of the unique capabilities that AM and 3DP have to offer. I personally think that the use of AM/3DP for light-weighting is one of it’s most exciting possibilities and one that could play a key part in the sustainability of design and manufacturing in the future.
        • Like
      • 3 replies
×

Important Information

Welcome to the Ultimaker Community of 3D printing experts. Visit the following links to read more about our Terms of Use or our Privacy Policy. Thank you!