Jump to content

UM2 temp error

Recommended Posts

Posted · UM2 temp error

Hello to all,

i have a problem with my UM2 bought on 2014.

i have both errors temp (bed and sensor). i've changed the bed and the pt100 (taken from my UMO+) and put the new firmware but it's the same shit. Some prints go the end but some not, in general mostly not. Do i need to change the mainboard ?


Share this post

Link to post
Share on other sites
Posted · UM2 temp error

So there are 3 errors. I'm not sure which 2 you get. Any of the 4 will halt a print. 1 is bed related. 2 are nozzle related. here they are:

ultimaker.com/ER01 Temp sensor

ultimaker.com/ER02 Temp sensor BED

ultimaker.com/ER03 Heater error

The heater error is when it doesn't heat up fast enough. The first 2 errors are never the heaters fault. You can get the temp sensor errors if your printer is below freezing temperatures when you turn it on (a more common problem than I would have thought - some people print in their cold garage).

Anyway if you get the first 2 errors there is absolutely no reason to touch the heater.

It's common for these sensors to fail above around 200C. You can't solder them because solder melts at these temps (lead solder 250C, lead free solder about 200C) so they are crimped. Some people have very carefully dremeled the temp sensor apart and repaired.

The newer temp sensors from 3dsolex and Ultimaker are just much more reliable than the ones from 2 years ago. I think you should just "bite the bullet" and get a new temp sensor.

The temp sensor on the bed is completely different. It's soldered in. It's very very rare for that to fail - I mean you can get the error but it's always the wiring is loose somewhere - most often at the connector on the bed - either the screws aren't tight or the solder connection breaks where the screw connector is soldered to the board. You can push and pull on that connector while the printer is on displaying bed temp and you might see the temp jump from 20C to 100C or 0C in an instant. if so then the problem is near that connector.

I've never heard of a bad PCB on a UM2 causing these errors. It's possible in theory but - it's all solid state. It just seems unlikely.

When you turn the printer on and just look at nozzle and bed temps. It should read around 20C (room temp). Does the temp just sit there? Or does it bounce around? If it bounces around then maybe it *is* the PCB.

  • Like 1

Share this post

Link to post
Share on other sites
Posted · UM2 temp error

thank you for your precious advice Gr5,.. the only things that were not checked are the bed cable and the mother board, the bed and the pt100 came from my UMO+, she printed about 3h00...these parts are new..I will check my motherboard as soon as possible..Mostly i've seen that the error came when you put on the UM, mine begin the print and sometimes it's ok, sometimes not..

i hope it is the cable..

thank u again.

Share this post

Link to post
Share on other sites
Posted · UM2 temp error

Look where the cable connects to the heated bed. There are 4 screws. That part often has a bad solder connection - especially since you removed it from the old bed to the new. I bet you just need to reheat the solder to let it flow again. Here is an old picture someone posted where you can see the 4 solder pads:


Share this post

Link to post
Share on other sites
Posted · UM2 temp error

hello everybody,

sorry for the late answer...

after have checked the cable, the motherboard was guilty ...

i've taken the UMO's and now, my UM2 is ok...

thanx to all.

Share this post

Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Our picks

    • January 22nd  | Ultimaker webinar 'Learn how to choose the right composite material'
      We’ll teach you how to choose the right composite material for your application in our new 40-minute webinar. You will learn how to: 
      • Make the perfect choice between glass and carbon fiber 
      • Identify more high-value applications that would benefit from composites 
      • 3D print advanced materials with the right settings 
      • Select the best materials for 3D printing end-use parts 
      • Use dual extrusion to take composite 3D printing to the next level 
      • 0 replies
    • Does your company use Ultimaker? Know one that does? Let us know!
      If your company uses Ultimaker in any capacity, we'd love to hear about it! If the story is there, and you're up for it, maybe we can work together to create a story that will be featured on the site. Here are examples of..
      • 18 replies
  • Create New...

Important Information

Welcome to the Ultimaker Community of 3D printing experts. Visit the following links to read more about our Terms of Use or our Privacy Policy. Thank you!