Jump to content

Unebenheiten über die Höhe?


bulior

Recommended Posts

Posted · Unebenheiten über die Höhe?

Ich habe Unebenheiten in z richtig und bekomme diese einfach nicht weg. Habe bereits die Bewegungsparametern (Acceleration, jerk) variiert, jedoch ohne Erfolg.

Die Temperatur des Materials wurde ebenfalls variiert und brachte kein Erfolg.

Druck information:

Ultimaker 2 Extended

Nozzle diameter:  0.4 mm

Printing speed:      30 mm/s

XY jerk:                    8 mm/s

XY Acceleration: 700 mm/s2

Layer height:        0.2 mm

Hatchbox ABS 215°C

Habt ihr evtl. Tipps wie ich den Fehler beheben könnte?

20170209_132941.thumb.jpg.522796dc8ac189592268be47a79c6b08.jpg

20170209_132941.thumb.jpg.522796dc8ac189592268be47a79c6b08.jpg

  • Link to post
    Share on other sites

    Posted · Unebenheiten über die Höhe?

    Hallo bulior,

    Ich kenne deine ABS-Marke nicht, aber 215° klingt für mich für ABS viel zu wenig. Versuch mal mindestens 235°.

    Welche Einstellung hast du für den Lüfter gewählt? (auch hier max. max. 50%, bei deinen Teil würde ich nicht über 25% gehen)

    Gruß Gerd

  • Link to post
    Share on other sites

    Posted · Unebenheiten über die Höhe?

    Vielen Dank Dir. Konnte das Problem lösen.

    Es lag am Extruder-Schrittmotor ...

    Das rechte Teil hat ebenfalls Unebenheiten, die jedoch durch Schrittverluste des noch zu schwachen Ersatzmotors hervorgerufen werden. Motor ist neu bestellt.

    5a33273c15afb_IMG_2017-02-12222142.thumb.jpg.8e24eb0dd1a68f49eeffdee9bdfe60b6.jpg

    Soweit vielen Dank ;)

    5a33273c15afb_IMG_2017-02-12222142.thumb.jpg.8e24eb0dd1a68f49eeffdee9bdfe60b6.jpg

  • Link to post
    Share on other sites

    Posted · Unebenheiten über die Höhe?

    Hi,

    das rechte sieht allerdings immer noch nicht so richtig sauber aus. Überprüfe mal die lange Z-Schraube. Am besten sauber machen und etwas von der grünen Paste darauf schmieren.

    Zusätzlich wäre es interessant zu wissen ob diese übrigbleibenden Aussetzer immer auf der gleichen Höhe auftreten.

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • Introducing Universal Cura Projects in the UltiMaker Cura 5.7 beta
        Strap in for the first Cura release of 2024! This 5.7 beta release brings new material profiles as well as cloud printing for Method series printers, and introduces a powerful new way of sharing print settings using printer-agnostic project files! Also, if you want to download the cute dinosaur card holder featured below, it was specially designed for this release and can be found on Thingiverse! 
          • Like
        • 10 replies
      • S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
        (Sorry, was out of office when this released)

        This update is for...
        All UltiMaker S series  
        New features
         
        Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
          • Like
        • 0 replies
    ×
    ×
    • Create New...