Jump to content
Ultimaker Community of 3D Printing Experts

Good Settings for Support Structures using Cura


Recommended Posts

Posted (edited) · Good Settings for Support Structures using Cura

Hi folks,

I've been mostly printing with my Ultimaker 2+ without supports, since I design my models mostly myself (examples). However I want to dive into the topic supports so I can also print models which I downloaded from various websites. Take this little helmet for example. The whole thing is 7cm wide and 5cm high.

skyrimhelm.jpg

First of all, yes, I would have saved material if I had printed the model upside down. I did this on purpose so I don't have to remove the supports from the topside, giving it a nice and clean finish.

Anyway, it took me over one hour to remove all the supports. It was really a pain. The removal wasn't easy at all, it felt so tightly connected to the main structure. I don't think that this is how it's supposed to work. Especially when I watch some YouTube videos and see how easily and effortlessly other people remove their support structures.

So I want to ask, is there maybe a a better setting or a a "go-to-configuration" for these support structures, making them easier to remove? Here are the settings I used (losely translated from my german version of Cura 2.3.1)

support structure activated: yes

where to place the stuff: everywhere

angle for overhangs: 45°

pattern of the structure: zickzack

connect zickzack elements: yes

density of the structure: 15%

By the way, I'm using the original Ultimaker Silver PLA Filament (Link).

I heard a lot of people recommend to use Simplyfy3D for support structures, but I thought I give Cura a try before spending 150$ on it, since I am using Cura for everything else so far and I'm quite happy with it.

I'm looking forward to you answers!

Thanks a lot,

Marius

Edited by Guest
  • Link to post
    Share on other sites
    Posted · Good Settings for Support Structures using Cura

    Meshmixer is free and it great for generating support but CURA now has a lot of options.

    Adjusting X/Y distance helps stop support going into tight corners that are difficult to remove.

    Increasing the support z distance can help stop it sticking to much and using support interface helps.

    Don't print to fast or hot as this will cause it to stick more.

    Using small nozzles make a huge difference in how easy it is to remove support. A 0.4mm nozzle at 0.1mm layers has a similar print time of a 0.25mm nozzle at 0.1mm layers if there are no big flat surfaces.

    I normally use support grid as it comes off in one piece. But haven't tried all the new types yet.

  • Link to post
    Share on other sites
    • 3 weeks later...
    Posted (edited) · Good Settings for Support Structures using Cura

    I am finding that the 'use towers' and 'conical support' to be helpful in limiting the amount of support needed. I have gone as low as 8% support amount with 10mm as the maximum width and 2mm the minimum width. It will tower out nicely to still make the 'cradle' that the print rests upon.

    Edit: I have also found it can compensate for 'Touching build plate only' rahter than always using 'everywhere'.

    Edited by Guest
  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • 20 Visiting our virtual showroom

      1. 1. Have you visited our virtual showroom before?


        • Yes
        • No
      2. 2. If yes - what content did you find most interesting?


        • Information about Ultimaker ecosystem
        • Applications & application stories
        • Customer success stories
        • Webinar sessions
        • Material wall & ecosystem partners
        • New product introduction; software subscription plans
      3. 3. What of the below would make you consider visiting (again)?


        • New Live Ultimaker Webinar streams
        • ‘Ask Me Anything’ with industry experts or Ultimaker staff via main stage and public chat
        • New customer success stories
        • New applications
        • Presentations/news from ecosystem partners
        • Opportunity to meet representatives for an interactive tour
        • Helpful videos like Software tutorials
        • Other; leave input in a comment below!

    • Our picks

      • Ultimaker turns 10: A look back
        Ultimaker is turning 10 years old and that means it is story telling time! We'll explore 2010-2014, traveling through the evolution of the business from the Protobox and Ultimaker Original, to the major leaps forward with the Ultimaker 2 and Ultimaker 3.
          • Like
        • 0 replies
      • Ultimaker Transformation Summit
        Visit our virtual showroom and learn more about the Ultimaker ecosystem!
        • 14 replies
      • New here? Register your Ultimaker for free 3D printer onboarding course
        Hi,
         
        Often getting started is the most difficult part of any process. A good start sets you up for success and saves you time and energy that could be spent elsewhere. That is why we have a onboarding course ready for
        Ultimaker S5 Pro Bundle, Ultimaker S5, Ultimaker S3 Ultimaker 2+ Connect.   
        They're ready for you on the Ultimaker Academy platform. All you need to do to gain access is to register your product to gain free access. 
        Ready? Register your product here in just 60 seconds.
          • Like
        • 0 replies
    ×
    ×
    • Create New...