UltiMaker uses functional, analytical and tracking cookies. Tracking cookies enhance your experience on our website and may also collect your personal data outside of Ultimaker websites. If you agree with the use of tracking cookies, click “I agree, continue browsing”. You can withdraw your consent at any time. If you do not consent with the use of tracking cookies, click “Refuse”. You can find more information about cookies on our Privacy and Cookie Policy page.
Posted
· Temperatur Druckdüse OlsenBlock zu niedrig
Ev. wäre Ursachenbekämpfung besser als Symptomtherapie? Empfehlung: Überprüfe, ob Temperatursensor und Heizpatrone noch vollständig im Block drin sind und ob Sie guten thermischen Kontakt haben. Ev. kannst Du da mit etwas Kupferfett rund um die beiden Elemente herum im Block drin nachhelfen.
Posted
· Temperatur Druckdüse OlsenBlock zu niedrig
Und welches Fan Mount verwendest du?
Wenn du noch das alte UM2 verwendest, wie hier zu sehen
(Bild Zufällig gesehen)
Dann musst du viel weniger Lüfter einstellen, da diese jetzt direkt auf der Nozzle blasen.
Meine Empfehlung ist entweder das von UM2+ zu besorgen, oder dir ein eigenes zu drucken (gibt einige auf youmagine oder ähnliche Seiten). Mit den richtigen Materialien hält das auch ganz gut.
Gruß Gerd
P.S.:
herbert said:
leider stimmt jetzt die Drucktemperatur nicht mehr, wenn ich vorher PLA mit 210°C gedruckt habe muss ich jetzt mind. 250°C einstellen, dass es wieder passt.
Was meinst du damit? Hast du nachgemessen oder ist das nur eine Empfindung.
Ursache wurden ja schon erwähnt.
Link to post
Share on other sites
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more.
S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
(Sorry, was out of office when this released)
This update is for...
All UltiMaker S series
New features
Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
Recommended Posts
Dim3nsioneer 557
Ev. wäre Ursachenbekämpfung besser als Symptomtherapie? Empfehlung: Überprüfe, ob Temperatursensor und Heizpatrone noch vollständig im Block drin sind und ob Sie guten thermischen Kontakt haben. Ev. kannst Du da mit etwas Kupferfett rund um die beiden Elemente herum im Block drin nachhelfen.
Link to post
Share on other sites
zerspaner_gerd 382
Und welches Fan Mount verwendest du?
Wenn du noch das alte UM2 verwendest, wie hier zu sehen
(Bild Zufällig gesehen)
Dann musst du viel weniger Lüfter einstellen, da diese jetzt direkt auf der Nozzle blasen.
Meine Empfehlung ist entweder das von UM2+ zu besorgen, oder dir ein eigenes zu drucken (gibt einige auf youmagine oder ähnliche Seiten). Mit den richtigen Materialien hält das auch ganz gut.
Gruß Gerd
P.S.:
Was meinst du damit? Hast du nachgemessen oder ist das nur eine Empfindung.
Ursache wurden ja schon erwähnt.
Link to post
Share on other sites