Jump to content

CURA Infill overlap and skin overlap percentage is not present in the printing

Danielrug05

By Danielrug05
in UltiMaker Cura

 Share

Recommended Posts

Danielrug05

Danielrug05 0

Posted
Posted · CURA Infill overlap and skin overlap percentage is not present in the printing

Hi,

I am trying to print with CURA 3.0.4 and this happened:

IMG_5265.thumb.JPG.f8b376132de608c2f0df0a62541eda3f.JPG

IMG_5266.thumb.JPG.bd562ee3033ac28e5e35802d9ecb8402.JPG

IMG_5267.thumb.JPG.aac36d6c6ca46cd82827aa54ea2f8032.JPG

In one of them you will see the same piece printed with CURA version 15.04.2 and the other with 3.0.4. When i tried to print FLEX, using the 3.0.4, the skin, inner wall and infill are separated from each other as you can see. The printed piece has numerous flaws compared to the one printed with the older software. what can i do to correct this? i have tried increasing the infill and skin overlap percentage up to 20% and the result is the same.

Thank you.

IMG_5265.thumb.JPG.f8b376132de608c2f0df0a62541eda3f.JPG

IMG_5266.thumb.JPG.bd562ee3033ac28e5e35802d9ecb8402.JPG

IMG_5267.thumb.JPG.aac36d6c6ca46cd82827aa54ea2f8032.JPG

    • Link to post
    Share on other sites
    • 5 weeks later...
    riodoro1

    riodoro1 0

    Posted
    Posted · CURA Infill overlap and skin overlap percentage is not present in the printing

    I just stumbled upon this topic looking for solutions myself.

    Had the same problem with the update, this actually forced me to use older cura, now even on the older software I have noticed this issue and wanted to ask if by chance You found a way to correct this. I think it might be an under extrusion issue.

    • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
     Share
    Go to topic listing

    • Our picks

      • UltiMaker Cura 5.7 stable released

        UltiMaker Cura 5.7 stable released

        ArunC posted a topic in UltiMaker Cura,

        Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
         
          • Like
        • 18 replies
        MariMakes

        Picked By

        MariMakes,

      • Release Notes: S-Line Firmware 8.3.0 (Latest)

        Dustin posted a topic in Firmware,

        S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
        (Sorry, was out of office when this released)

        This update is for...
        All UltiMaker S series  
        New features
         
        Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
          • Like
        • 0 replies
        MariMakes

        Picked By

        MariMakes,
      View All
    ×
    ×
    • Create New...