Jump to content
Ultimaker Community of 3D Printing Experts

Dimensional accuracy problem with holes

Recommended Posts


I'm having problems to print separate parts which should fit together. So I created a test print.

I have a cube with the dimensions of 20x20x10mm

I subtract another cube with 10x10x10mm from it so I get a hole of 10x10mm in the middle of the first cube.


When I print this with my Ultimaker 3 all dimensions are perfect except the hole in the middle. It is 0.5mm to small in both dimensions (x/y).


I found the "Horizontal Expansion" parameter in Cura which allows me to correct this but this affects my outer dimensions as well.

I tried various materials (PLA, ABS, InnoFlex Pro1) and got the same results.


Does anyone have an explanation for this behavior? 

Any suggestions how can I avoid this?

Share this post

Link to post
Share on other sites

Are you taking your measurement from the top of the cube (as printed) or the bottom of the cube? It would be helpful if you could post some of your settings; layer height, print speed(s), temps, wall line width and no. of walls., outer before inner walls, alternate extra wall; compensate wall overlaps, infill before walls.


I am surprised you have such a large error.

  • Like 1

Share this post

Link to post
Share on other sites

This is very common.  vertical holes too small.  It's much worse with round holes than square holes - with square holes typically it's only the corners that are a problem and typically the sides are fine.  0.5mm shrunk diameter is typical although I usually see closer to 0.3 shrinkage and I typically add 0.4mm to my vertical holes in CAD as a first estimate.


To answer your question - this is because PLA cools quite quickly (in milliseconds) as you are printing and so it shrinks a bit so it's under tension - PLA sticks to itself when liquid - like snot - like mucus.  This is a very very useful property (try printing with PVA - horrible in comparison) but when you are printing it's like a liquid rubber band and when printing circles it pulls inward or if squares it pulls inward mostly on the corners.


There are other reasons why holes are too small - CAD software doesn't output circles but instead polygons with each point on the circle and that makes the polygon *smaller*.  This is typically only an additional 0.1mm so not as significant (depends on how many sides to your polygons).  Also PLA shrinks by about 0.3% - also not as significant as in your example .3% of 1cm is .03mm.

  • Like 1

Share this post

Link to post
Share on other sites

Oh by the way - so the problem is worse near the heated bed but the heated bed is so amazingly helpful for other reasons it's worth it.  But if ALL your parts are smaller than 1cm you could lower the heated bed to 45C.  Or even go with blue tape instead (but if you use blue tape you have to wash it first with isopropyl alcohol).  Also if you print cooler the problem isn't as bad.  I've printed PLA as low as 180C but you have to print much slower as it's more like peanut butter than honey at that temperature.  I usually print at 200C on UM3.

Share this post

Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Our picks

    • Ultimaker Cura | a new interface
      We're not only trying to always make Ultimaker Cura better with the usual new features and improvements we build, but we're also trying to make it more pleasant to operate. The interface was the focus for the upcoming release, from which we would already like to present you the first glance. 
        • Like
      • 130 replies
    • "Back To The Future" using Generative Design & Investment Casting
      Designing for light-weight parts is becoming more important, and I’m a firm believer in the need to produce lighter weight, less over-engineered parts for the future. This is for sustainability reasons because we need to be using less raw materials and, in things like transportation, it impacts the energy usage of the product during it’s service life.
        • Like
      • 12 replies

Important Information

Welcome to the Ultimaker Community of 3D printing experts. Visit the following links to read more about our Terms of Use or our Privacy Policy. Thank you!