Jump to content
Ultimaker Community of 3D Printing Experts
  • Sign Up
Tiger91

Printing with PP?

Recommended Posts

Posted · Printing with PP?

I just got some PP to test out on my UM3...

 

I'm pretty disappointed - it has the worst adhesion possible, even with glue/hairspray. I know that one of those expensive build plates is recommended for this material, but I was wondering if anyone had luck printing with just the normal glass buildplate?

 

Also, if you do use the adhesion base, what are the largest prints you've done with it?

 

Any tips?

Share this post


Link to post
Share on other sites
Posted · Printing with PP?

Hi @Tiger91,

 

luckily i could use those famous adhesion sheets from Ultimaker. And i printed a very small part. Lately i discovered some bubbles under the sheet where the corners of the part were - so, adhesion on the sheet was very good.

Maybe you could try something like book wrapping foil or Tesa 4309? I didn't test one of them but i would try if i had none of these UM-Sheets.

 

And maybe you could cover your UM with a card-board-box to keep the heat inside? Every bit of warmth helps :-)f

 

Cheers,

dxp

Share this post


Link to post
Share on other sites
Posted · Printing with PP?

Hi!

 

PP and adhesion is indeed complicated. That's why it's recommended to use the adhesion sheets (these work pretty well).

 

PP is known to stick to basically nothing so you can try different things but it's most likely it will fail.

 

Tips for adhesion as you probably know: 

 

Large brim and pretty close levelling, you may want to change your first layer height to 0.2 or 0.1 for an extra squish.

 

Try blue tape maybe? But the best would be the adhesion sheets (you can buy that directly from your local reseller)

Share this post


Link to post
Share on other sites
Posted · Printing with PP?

I've had great success with PP by using the glassplate, then spraying it with printafix , waiting a bit, then spraying again. just a 3 or 4 layers of printafix, then printing with the default cura settings. 

no more adhesion problems for me :)

I actually have a special glassplate for PP that is completely coated in printafix and i just never clean it.. works like a charm.

Share this post


Link to post
Share on other sites
Posted · Printing with PP?

One straightforward solution if you don't have printafix is to use the wide (normally brown) packing tape used for sealing up boxes for shipping.  I think this tape is actually PP, and PP really only likes to stick to itself, but the adhesive on the other side allows the tape itself to stick to the glass plate.

 

I've found this to be very effective, the only downside is that when removing the print sometimes it doesn't come away cleanly and some small parts of the tape come away stuck to it that you need to clean off.  I've produced PP prints that are as large as the buildplate of the UM2 using this technique with no problems of loss of adhesion.   

  • Like 1

Share this post


Link to post
Share on other sites
Posted · Printing with PP?
On 2/26/2018 at 7:31 AM, SteveCox3D said:

One straightforward solution if you don't have printafix is to use the wide (normally brown) packing tape used for sealing up boxes for shipping.  I think this tape is actually PP, and PP really only likes to stick to itself, but the adhesive on the other side allows the tape itself to stick to the glass plate.

 

I've found this to be very effective, the only downside is that when removing the print sometimes it doesn't come away cleanly and some small parts of the tape come away stuck to it that you need to clean off.  I've produced PP prints that are as large as the buildplate of the UM2 using this technique with no problems of loss of adhesion.   

I will have to try that - do you know a good brand/location that would give best results?

Share this post


Link to post
Share on other sites
Posted · Printing with PP?

I think most brands of packing tape should work.  They tend to be made from polypropylene or polyester, and you want the polypropylene type.  So if you buy some see if it specifies which material it is.  It worked for me with the tape I already had which didn't have any material info on it - maybe I got lucky and it was PP. 

Share this post


Link to post
Share on other sites
Posted · Printing with PP?

Hi Steve, You are great!!!

 

I have tried your solution and works perfectly!! The packing tape is the solution, I have used a transparent one and it works!

 

Thanks a loooottt!!

 

If you come to Spain you are invited to enjoy with us !!

 

Best Regards

  • Thanks 1

Share this post


Link to post
Share on other sites
Posted · Printing with PP?
On 10/27/2018 at 6:29 PM, Cosomo said:

Hi Steve, You are great!!!

 

I have tried your solution and works perfectly!! The packing tape is the solution, I have used a transparent one and it works!

 

Thanks a loooottt!!

 

If you come to Spain you are invited to enjoy with us !!

 

Best Regards

Glad it worked out! This forum is all about helping each other, so it's great to get your feedback that this solved your problem.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Our picks

    • Talking additive | The 3D printing podcast
      Why should we be the only ones asking questions? Join us and ask Jabil all your questions on September 22nd 5pm CET
        • Like
      • 2 replies
    • Ultimaker masterclass: Optimizing your Ultimaker Cura workflow
      Save your seat for either broadcast on September 23.
      What will you learn?
      · Best practices for iterative print preparation and every lesson you should learn from each print
      · The right way to use per-object settings and when they are most useful
      · Easy-to-use resources for anyone who wants to develop their own printer definitions, plugins, or print profiles
      · How to optimize print profile settings and whether to “keep” or “discard” changes
      · When is the right time to export your drawing from CAD? (Based on Ultimaker Cura’s surprising power as 3D control software)
      · And a whole lot more tips and tricks!
       
      How can I join?
      This free masterclass will take place twice:
      1. 11am CEST (5pm SGT, 5am EDT)
      2. 5pm CEST (11am EDT, 8am PDT, 11pm SGT)
        • Like
      • 0 replies
    • Do you use 3D printing at work? Let us know
      It doesn't matter if you are using 1 Ultimaker or 10, there is inspiration in everything. We're looking for ...
      • 1 reply
×
×
  • Create New...