kmanstudios 1,120
3 hours ago, Modified_Gemini said:What I'm after? Basically, an apology.
Not going to happen. You see, I am not sorry for what I thought was right. I acknowledged the difference. It is you that have made this personal for yourself. I have altered my position based off good information by another person other than yourself.
3 hours ago, Modified_Gemini said:Or just stop replying is cool
Why should I not reply when you keep dredging this up and confusing timelines?
3 hours ago, Modified_Gemini said:You still cannot understand the you caused this by arguing your opinion over the facts I presented.
You cannot understand that the 'facts' you presented were not really an explanation. It wa basically because "You said so." You hold no high ground on that issue. You keep drawing a difference between overlapped and stacked when they are the same thing in a constructive sense. In a programming sense and how properties are assigned, it does make a difference.
3 hours ago, Modified_Gemini said:like it had any bearing on the conversation.
It dos when you are trying to say you were giving out proper information, the role of a teacher. That is the substance of being here. I am trying to learn and those that are responsible in their vastly superior knowledge try to pass this on by way of explanation, not berating someone struggling to learn and understand. That makes them teachers, and it does not make you one. If you cannot see that then all of this is lost on you.
It is too bad that you got your feelings hurt. But, it is you who has chosen to make this personal. It is you that has chosen to keep this alive even after I changed positions way back just because you cannot see that your explanations were inferior to someone else's information. Even up to your last post, you kept trying to say that I had not changed positions.
Even as of yesterday, this was your position:
3 hours ago, Modified_Gemini said:I mean, do you still think you print single walls?
And, when you make these kind of statements that I can fully understand what is being said:
3 hours ago, Modified_Gemini said:As how is it configured as .35mm?
Cura is set to a 0.35 line width by default.
It is configured to that line width. Simply opening the program would have shown you that. But you fail to see that this type of misinformation can lead to a lack of trust in your information.
Here is the gist of it all as I see it. You got your feelings hurt because I accepted someone else's explanation over your's. This is not an issue I am concerned about. I accepted the new information when presented in a way that I could understand. For me, that is growth. Your feelings are not anywhere near my priority. Acknowledgement of ignorance was not good enough for you. A change of position is not good enough for you. I have even acknowledged that you, in fact, do have superior knowledge and that still is not good enough.
So, if that is not good enough, then you will be left unhappy as I am not going to apologize for defending a position that, for all the information at my command at that time, said otherwise to your position.
Oh, and by the way, stacking and overlapping as well as layering, heap, load, etc. are synonyms. It deals with arrangement of layers. But this does not approach the issue of each wall having separate properties. Only one person made that clear and he got thanks for that.
Edited by kmanstudios
Recommended Posts
Top Posters In This Topic
30
30
25
8
Popular Days
Mar 10
21
Mar 9
14
Mar 7
11
Mar 11
10
Top Posters In This Topic
Modified_Gemini 30 posts
kmanstudios 30 posts
burtoogle 25 posts
ghostkeeper 8 posts
Popular Days
Mar 10 2018
21 posts
Mar 9 2018
14 posts
Mar 7 2018
11 posts
Mar 11 2018
10 posts
Popular Posts
ghostkeeper
We get a lot of questions about this actually. We use about 7/8ths of the nozzle size in Ultimaker's printers because adjacent lines tend to adhere better together then. Because the nozzle is a b
kmanstudios
I am not sure what you are designing, a pic would be most helpful. But, this is how I cracked the spiralize/vase mode print. It may sound silly, but it showed me the basics of how it could work.
burtoogle
The way Cura works at the moment, when not using spiralize mode, all walls have to have an even number of lines. It modifies the flow of the second line to try and compensate for the overlap but the i
Posted Images
Modified_Gemini 2
I explained they are not "stacked" on each other. they are overlapped.. Stacked would mean a new wall is printed on top of the original. Overlapped means they are not stacked. It is slightly offset and the slow 1% extrusion is creating a new wall that is joined to the previous wall.. HUGE difference in realities.
I did explain myself, also The first reply understood EXACTLY what I was talking about. It is not my fault you chose to jump into a conversation you did not grasp
Again no, you ignored the facts given to you because "didn't understand it". There is a HUGE difference between 1 and 2. The real explanation was set forth in the beginning with my gcode analysis AND confirmed with the very first reply (which you chose to ignore as well).
Sorry, but its completely relevant. The gcode shows the EXACT movements of the toolpath. Not what you think you see in a picture.
Im actually a happy go lucky kinda guy. I just didn't appreciate someone arguing their opinion over the facts I given. (again facts that from the first reply understood. because you couldn't is not my fault)
no, I turned it off on my phone. its like really super annoying. But youre really doing your dammdest to deflect.. my spelling has nothing to do with the gcode that you cannot understand anyways.
What I'm after? Basically, an apology. Or just stop replying is cool. You still cannot understand the you caused this by arguing your opinion over the facts I presented. And you did this on the grounds because "you did not understand". I was arguing and trying to explain to who I thought understood the basics of 3d printing. Which you didn't. Which brings to light many points. Why were you arguing your opinion over facts I presented? Yet you claimed me to be a troll? You said my alternative facts? Seriously, what kind of teacher are you? A student provides evidence and you ignore it because its above your paygrade of understanding?
Funny you pointed out your a teacher... like it had any bearing on the conversation. it obviously didn't grant you any understanding of my post from the get go. Yet you try to point out I'm being superior? Well I can hold my breath for 10 seconds. I guess were even..
Link to post
Share on other sites