Jump to content
Ultimaker Community of 3D Printing Experts

Power Trip at the beginning of print


Recommended Posts

Posted · Power Trip at the beginning of print

Hi,

 

I am facing the issue that when I start my print job, UM3 move to switch the nozzle. Before it could reach, there seems to have a power trip causing UM3 to stop.

See video on YouTube https://youtu.be/Fi_AXEE4Mg4

It had occurred during my last 3-5 prints where it still can print for about 15min before power trip.

And now, it just failed whenever I start my print.

Need help to debug this issue.

 

Thanks & Best regards

Eric

  • Share this post


    Link to post
    Share on other sites
    Posted · Power Trip at the beginning of print

    First make really really sure your power cable isn't loose.  There is a cylindrical clip thing on the outside of the plug.  The cord should not come out unless you slide that back - make sure it's completely latched into the printer and also make sure the AC cord is firmly in the power brick.

     

    If that is all fine then it's 90% the power brick.  They shut down very briefly if they think too much power is being drawn and the power failure is only milliseconds so it looks just like a reboot but it's really a power glitch.

     

    Contact your reseller about getting a new power brick.

    • Thanks 1

    Share this post


    Link to post
    Share on other sites
    Posted · Power Trip at the beginning of print

    Hi, Eric,

     

    I've only seen this a couple of times; your case is unusual because normally if I see a power cycle like this it's right at the start of the print. Does the same thing also happen if you manually heat both Cores and the bed without the motors moving?

  • Share this post


    Link to post
    Share on other sites
    Posted · Power Trip at the beginning of print

    Hi,

    Thanks for the recommendation.

    I had tired to heat up the 2 core to 150 degree C and base plate to 85 degree C.

    No power cycle occurred. What is the recommended test temperature?

     

    Any other way of testing if the power brick is the issue?

     

    regards

    Eric

  • Share this post


    Link to post
    Share on other sites
    Posted · Power Trip at the beginning of print

    Turn the fans on from the menu.  Set all 3 heaters to a temperature above what they currently are (at least 20C) so they are all on full.  Then home the x,y axes.  That moves everything but the extruder (the Z doesn't move much during a print).

     

    Anyway I saw your video.  Unless you have a loose cable, it's the power brick.  This is common enough that I've seen this 3 times on the forum even just in the last 3 months and replacing the brick always fixes it.

     

    You should be able to get a replacement for free from your reseller.  Or you can just buy one.  If you buy one I recommend this without the "T".  "GS" I like better than "GST".  GST is more efficient but GS has a larger margin.  In other words the GS one can put out more power.  But the GST one should work fine with your printer - you just need a new one.

     

    Any power supply that puts out 24V and 10A (or more than 10A) will work fine but in that case you would need to cut the power cable and do some soldering.

     

    Meanwell power supplies.  

    GST220A24-R7B
    GS220A24-R7B

    • Thanks 1

    Share this post


    Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • Talking additive | The 3D printing podcast
        Why should we be the only ones asking questions? Join us and ask Jabil all your questions on September 22nd 5pm CET
          • Like
        • 3 replies
      • Ultimaker masterclass: Optimizing your Ultimaker Cura workflow
        Save your seat for either broadcast on September 23.
        What will you learn?
        · Best practices for iterative print preparation and every lesson you should learn from each print
        · The right way to use per-object settings and when they are most useful
        · Easy-to-use resources for anyone who wants to develop their own printer definitions, plugins, or print profiles
        · How to optimize print profile settings and whether to “keep” or “discard” changes
        · When is the right time to export your drawing from CAD? (Based on Ultimaker Cura’s surprising power as 3D control software)
        · And a whole lot more tips and tricks!
         
        How can I join?
        This free masterclass will take place twice:
        1. 11am CEST (5pm SGT, 5am EDT)
        2. 5pm CEST (11am EDT, 8am PDT, 11pm SGT)
          • Like
        • 0 replies
      • Do you use 3D printing at work? Let us know
        It doesn't matter if you are using 1 Ultimaker or 10, there is inspiration in everything. We're looking for ...
        • 1 reply
    ×
    ×
    • Create New...