Jump to content
Ultimaker Community of 3D Printing Experts

Home cover for Ultimaker 3


Recommended Posts

Posted · Home cover for Ultimaker 3
image.png.1bc992915d766dc7cb6c7c6f1522ac24.pngThis is a cover that I installed on my printer.

Since then my impressions have improved immensely.

They sell a cover for Ultimaker 3. But I find it unsightly and very expensive.

So carry out this idea, which is simple, cheap and aesthetic and works perfectly for me.

It deals with a superior frame, a cardboard laminated with a vinyl and folded in zip-zap (accordion). and some small guide pieces,

The cardboard is plasticized with a vinyl to which heat is applied with an iron,

The frame and the guide pieces then with the printer.

The printer also has a front cover, this is purchased.

Well you can see it in the video.
  • Like 3
Link to post
Share on other sites

Posted · Home cover for Ultimaker 3
7 hours ago, Swissengineer said:

Como la idea! pero ¿qué hay de la impresión PLA? También la acumulación de polvo me preocupa... 

Well I do not print in PLA, I print in ABS, HIPS, ASA, and I have not had any problem with dust,
With PLA, only make a couple of impressions, when you buy the machine, to test it, with the filament that came in the purchase.
But you gave me an idea about it.
And I'm going to place inside a small fan, making the air pass through a filter, composed of active carbon and fiber, the elements I already have, because I use them to filter the water of an aquarium that I own.
I'm going to do this not because of the dust, but because of the vapors that ABS gives off, ASA etc., which are not healthy. And the dust will filter it sim problem.
As soon as I have time, I'll do it and put it in the forum.
Thanks for the comment, you gave me a good idea.
  • Link to post
    Share on other sites

    Posted (edited) · Home cover for Ultimaker 3

    I like the idea. But I must agree that with the printhead moving between those edges in the slit (fore and aftward) I would think it would grind some dust into the environment.

    Edited by kmanstudios
    Had to change direction of movement
    • Like 1
    Link to post
    Share on other sites

    Posted · Home cover for Ultimaker 3

      Well, it does not produce dust, because the rubbing is between the plastic tube and the vinyl, with which the cardboard is lined,
    There are already many impressions that I have made with the cover, and I have not observed any wear.
    This cover is a prototype, I am designing a definitive one and in certain places I will be wearing a Teflon adhesive tape, which I was expecting to receive, and received today.
    And the rubbing site that you indicate will carry this Teflon tape. But in any case it does not produce dust.

  • Link to post
    Share on other sites

    Posted · Home cover for Ultimaker 3
    9 minutes ago, M-RAGA said:

     

     

    Pues explico como realice la cubierta y pongo los archivos.

    lo primero plastifique dos cartulinas por las dos caras, con este vinilo que venden para plastificar tela, pero plastifica perfectamente la cartulina,

     


    20180412_133324.thumb.jpg.ae4374471009422277248ead360ee524.jpg

    A las dos cartulinas y les realice unos dobleces en Zip zap de aproximadamente 15 mm, y un total de 42 o 43 dobleces, el ancho será de 32 cm. en un extremo  unos cortes como en la foto.

    Lo mejor es marcar con una regla y lápiz las distancias de 15 mm, y ayudarnos de una regla para que los dobleces queden iguales.

    20180412_124742.thumb.jpg.a47d6fa2ed6ce980efb8a9513a4994c8.jpg

    5acf44b2cbcd9_20180412_1313141.thumb.jpg.1ac24c815d7f035934d028f3e08b0697.jpg5acf4536a37be_20180412_1313391.thumb.jpg.1ca53ace742b70b9df583500903c2dbd.jpg

     

    Impresas las piezas de plástico de la cubierta, según están diseñadas se montan como indican las fotos, se imprimen dos de estas piezas.

     

    20180412_124036.thumb.jpg.1fcfea214d36ad7d31b429a032170a60.jpg20180412_124048.thumb.jpg.d5626e44a556246c5766f1546651ae26.jpg20180412_124115.thumb.jpg.34464b65d87544e1d618b024e3a81205.jpg20180412_124609.thumb.jpg.56236902cd97fd487e2ff4c05d5f1f28.jpg

    Para montar el armazón utilice tornillos m3, unas tuercas insertables, y unos clips.

    20180412_132345.thumb.jpg.4d41f1565e7b0cab9378f3c634b72bce.jpg

    Se intrduce el pliege cortado en la pieza de plastico y se atornilla.

     

    20180412_124916.thumb.jpg.1a3994045d1834baec1f6bf3ca9b01d9.jpg

     

    Con los clips se sujeta el otro extremo en las piezas de platico como en las fotos

    20180412_125054.thumb.jpg.adc5bb628881c79b7245c0f5abfd257d.jpg

    20180412_125223.thumb.jpg.bc559e74167ef67cfaccd9759b3fb3ba.jpg

    y se monta el armazón. yo los uní con cortes de varilla de aluminio, pero se puede utilizar cualquier tipo de varilla,

    20180412_125349.thumb.jpg.e9e1c3f312860b06cf5d4add877093d6.jpg

     

    Imprimí las piezas con filamento ASA, natural, con ASA blanco supongo que el tono seria más parecido al de la impresora, lo digo para el que quiera seguir la estética,

    20180412_125727.thumb.jpg.6d8e9abc6b19e47c2cde5c2eba3fb4ce.jpg

     

     

     

     

     

    2-EMPUJADOR.stl

    2-LARGERO LATERAL.stl

    EAQUINA TRASERA IZQUIERDA.stl

    ESQUINA DELANTARA DERECHA.stl

    ESQUINA DELANTERA IZQUIERDA.stl

    ESQUINA TRASERA DERECHA.stl

    LARGERO FRONTAL .stl

    LARGERO TRASETO.stl

     

     

     

     

     

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
     Share

    • Our picks

      • New here? Get ahead with a free onboarding course
        Hi,
         
        Often getting started is the most difficult part of any process. A good start sets you up for success and saves you time and energy that could be spent elsewhere. That is why we have a onboarding course ready for
        Ultimaker S5 Pro Bundle, Ultimaker S5, Ultimaker S3 Ultimaker 2+ Connect.   
        They're ready for you on the Ultimaker Academy platform. All you need to do to gain access is to register your product to gain free access. 
        Ready? Register your product here in just 60 seconds.
          • Like
        • 11 replies
    ×
    ×
    • Create New...