Jump to content

Mit dem S5 ABS Drucken, obere Abdeckung notwendig und welches Stützmaterial


3D-Simon

Recommended Posts

Posted · Mit dem S5 ABS Drucken, obere Abdeckung notwendig und welches Stützmaterial

Wenn ich mit dem S5 ABS drucken will, benötige ich dafür eine obere Abdeckung. Oder reichen die serienmäßigen Türen aus ?

Für den UM3 gibt es ja so etwas.

 

Und welches Stützmaterial sollte ich verwenden ? Man liest im Netz dass PVA nicht so geeignet ist?

  • Link to post
    Share on other sites

    Posted · Mit dem S5 ABS Drucken, obere Abdeckung notwendig und welches Stützmaterial

    Hi @3D-Simon, hope you don't mind if I reply in English. My Deutsch is not so good. 

    You don't really need the top cover for ABS. Not for keeping the heat in that is, we would recommend to only use it in a well ventilated room due to the fumes. 

     

    Because of the doors, it keeps the draft out and the heat in, which according to our test is sufficient to achieve reliable results using (our) ABS. (That is what we tested, we didn't have the resources to test all available ABS). 

     

    PVA is not great for ABS, there is some layer bonding but not as great as with PLA for example. Breakaway material works better, but this may not be ideal if you need support material inside an object, instead of on the outside. 

     

    For your information, here is material compatibility list: https://ultimaker.com/en/resources/49799-material-compatibility

     

    Depending on your application, there may be other interesting materials to choose from. Depending if you need strength, chemical resistance or heat resistance, you may want to consider Tough PLA or Nylon.

     

    Out of curiosity, what are other details are important for you? Replacing an expensive Stratasys machine for an accessible Ultimaker sounds exactly what we think we can offer to many professional businesses. I would be interested to learn which other specifications are important for you to determine if it would be a good decision. 

     

    Looking forward hearing from you! 

  • Link to post
    Share on other sites

    Posted · Mit dem S5 ABS Drucken, obere Abdeckung notwendig und welches Stützmaterial

    Hi SandervG,

     

    will there be a support metarial for ABS in the near future? some competitors use hips filament.

     

    actually we use ABS because our products are made of ABS via plastic injection molding.

    In my opinion we don´t need that for 99% of out prototypes.

    Main reasons to replace the stratasys printer was the expensive filament ,the higher price of the successor series F123 and at least the expensive fixing cost (replacement cost of a print head was <2000€)

     

     

  • Link to post
    Share on other sites

    Posted · Mit dem S5 ABS Drucken, obere Abdeckung notwendig und welches Stützmaterial

    Das Breakaway Stützmaterial von Ultimaker ist mit Ultimaker ABS kompatibel. Der S5 kann auch HIPS drucken, einfach 2.85mm im Durchmesser muss es sein. Am Drucker muss dann einfach ein Material ausgewählt werden, dass eine ähnliche Drucktemperatur hat (z.B. PLA) und in Cura wäre ein eigenes Materialprofil anzulegen (oder ein anderes Profil einfach anzupassen). Bei einem eigenen Material reklamiert dann Cura Connect einen Material-Mismatch, der sich manuell übersteuern lässt.

  • Link to post
    Share on other sites

    Posted · Mit dem S5 ABS Drucken, obere Abdeckung notwendig und welches Stützmaterial

    Sorry for responding in English again. 

    We don't have HIPS in our own portfolio because of the chemicals required to dissolve it. Some research also showed these may affect the ABS negatively even. That is why we prefer to recommend Breakaway material if possible. 

    But like @Dim3nsioneer says, we have an open filament system, which means you can just use HIPS even if we don't offer it ourselves. The Ultimaker can still use it. We've actually recently announced partnership with some large chemical partners , so you should expect a large expansion of supported engineering materials soon! 

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • Introducing Universal Cura Projects in the UltiMaker Cura 5.7 beta
        Strap in for the first Cura release of 2024! This 5.7 beta release brings new material profiles as well as cloud printing for Method series printers, and introduces a powerful new way of sharing print settings using printer-agnostic project files! Also, if you want to download the cute dinosaur card holder featured below, it was specially designed for this release and can be found on Thingiverse! 
          • Like
        • 10 replies
      • S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
        (Sorry, was out of office when this released)

        This update is for...
        All UltiMaker S series  
        New features
         
        Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
          • Like
        • 0 replies
    ×
    ×
    • Create New...