Jump to content
Ultimaker Community of 3D Printing Experts
swatti

How to infill every 2-3 layers?

Recommended Posts

I have a large'ish nozzle
I do 100% infilled parts

I do low .2 wall layers

 

Doing infills every layers is kinda pointless. Takes LOTS of time and since i do 0.2mm (or lower) layers i could infilling every 2-3 layers and it would still look good and be durable. I did this back when i was using Simplify3D and it worked... But as we know, S3D is, well... Poopy. 

"Infill layer thickness" -option doesnt seem to do much of anything even if doubled or tripled. It still does infilling every layer.

Share this post


Link to post
Share on other sites

If a (part of a) layer is too thin to be printed at the 0.3mm layer height it will print it at the normal 0.15mm layer height.

I don't have any problems with Infill Layer Thickness here on the master branch, though... I have infill printed every other layer for the most part of my angled cube.

Share this post


Link to post
Share on other sites
3 minutes ago, bagel-orb said:

If a (part of a) layer is too thin to be printed at the 0.3mm layer height it will print it at the normal 0.15mm layer height.

I don't have any problems with Infill Layer Thickness here on the master branch, though... I have infill printed every other layer for the most part of my angled cube.


99/100% Infill?

Post me a project-file with your settings in it. I wanna see what i have different.

Share this post


Link to post
Share on other sites

99% of course; 100% infill makes no infill but uses top/bottom everywhere.

I'm on master, so I don't think you can use my project files.

If your problem keeps ocuring I suggest you make a new issue at github.com/ultimaker/cura and fill in the complete issue template.

Share this post


Link to post
Share on other sites

Can you install the normal version and give it a quick test? Does it show in the preview on master, i'd imagine it does or should. 

If its a problem with this version, i can give it rest for a while and/or make a topic on github.

I need to ficure out if its MY settings, this current version or something else.

Share this post


Link to post
Share on other sites

PROGRESS!

Its somehow connected to the pattern! 
Triangles seem to be able to do once every 2 layers but "lines" "grid" and "Zig Zag" can only do every 1 layer.

I'd say those three are the only patterns "viable" for good 100% (or 99%) infill. Infill crossing over existing ones is meant for less than 100% infilled models and doing fat lines that cross over existing lines would end up in bumps.

So, the question now is: How do i make lines, grid or zigzag every 2-3 layers? 😄

Share this post


Link to post
Share on other sites

EDIT: Forgot, this is on 3.4.1
I will test 3.5 and get back to you.

MAJOR BUG found in spaghetti infill.

I finally found a nice settings that work with spaghetti and do what the initial target was, but the spaghetti is broken, baaad.

Once a more complex than a test-cube is sliced, it makes random spot of infill into gigantic. Different flow, inset and extra volume -settings change how messed up it is but there doesnt seem to be a "trick" to getting a clean print.

Kinda sad, i printed the test-cube at hilarious rate and it all looked so good.

PIC1 - Copy.jpg

Edited by swatti
"oops"

Share this post


Link to post
Share on other sites

3.5 has bugs in spaghetti. Seems 2 walls has "least" bugs. Up that to 3 and things explode.

EDIT: Kinda hilarious, even the mighty Bondtech starts to tear into the filament when im ramming it in 0.9mm layers out of a 0.6 nozzle at 200mms. Even at 230c it wont melt fast enough and yes, i have the volcano.

Edited by swatti

Share this post


Link to post
Share on other sites

Perhaps it is not a bug. It could be trying to fill a large infill region from a small island above that.

Spaghetti infill was made for filaments which are especially fluid, so that the material can flow to the big regions below.

The layer view doesn't handle it like that, though.


Please attach a .curaproject file which produces the bug.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×

Important Information

Welcome to the Ultimaker Community of 3D printing experts. Visit the following links to read more about our Terms of Use or our Privacy Policy. Thank you!