Jump to content
SandervG

New: Ultimaker Cura 3.5

Recommended Posts

Posted · New: Ultimaker Cura 3.5
54 minutes ago, Adam324 said:

Sometimes it would go through the object if there are holes and end up trying to support something further up.

 

Indeed - it tries to support the three holes further up. It's more obvious if you switch back to "Support Placement = Everywhere".

I guess it's a bug (kind of...)

You can add a support blocker on this side though...

 

Share this post


Link to post
Share on other sites
Posted · New: Ultimaker Cura 3.5

I tried using blocker. Seems like it has a bug also as it did not work. Maybe if I set them in the holes... This is not kind of a bug it is a big bug 

Share this post


Link to post
Share on other sites
Posted · New: Ultimaker Cura 3.5

I took a look. All surfaces that look planar, are so. No holes in the areas of odd support. Object is fully manifold. What it is doing is trying to align with the holes in the top of the object (by orientation of printing) as if trying to get to them to support them.

Share this post


Link to post
Share on other sites
Posted (edited) · New: Ultimaker Cura 3.5
1 hour ago, R3D said:

I tried using blocker. Seems like it has a bug also as it did not work. Maybe if I set them in the holes... This is not kind of a bug it is a big bug 

 

Yea.  You have to put the blocker up in the hole as that is what it is probably trying to support.

If you only show 'Show Helpers', It is strange that it just stops.  It is not obvious it is trying to go up higher.  Definitely looks like a bug of some kind.

 

I tested it on 3.4.1 also and that support doesn't appear on 3.4.1.

Edited by Adam324
  • Like 1

Share this post


Link to post
Share on other sites
Posted · New: Ultimaker Cura 3.5
7 hours ago, Adam324 said:

Definitely looks like a bug of some kind.

I am going to have to agree that this is a bug if it is trying to support a hole that does not jut out. if you increase the support horizontal expansion, it should be able to reach up to the holes, but not what is happening.

Share this post


Link to post
Share on other sites
Posted · New: Ultimaker Cura 3.5

Graphic driver crash.
After while the video display (octoprint video stream) flicker, a few seconds later the graphic driver crash.

With Cura 3.4.xxx no problems.

 

OS: W10 64 Bit

Grafic: Nvidea

 

Share this post


Link to post
Share on other sites
Posted · New: Ultimaker Cura 3.5

guys why do we have to do a fresh installation of Cura each time there is a new release? Cant you make it so that its an update instead? nothing transfers over to the new installation and its kinda annoying having to redo everything again.

Share this post


Link to post
Share on other sites
Posted · New: Ultimaker Cura 3.5
9 hours ago, Bigbrit said:

guys why do we have to do a fresh installation of Cura each time there is a new release?

 

You don't. The idea is that Cura takes the configuration from the last version and upgrades it on the first launch of a new version. Is that not what's happening for you?

Share this post


Link to post
Share on other sites
Posted · New: Ultimaker Cura 3.5

Cura 3.5 fixed my "pause at height" issue with my S5, but now it seems to cause a "pause at height" issue with my UM 2+

 

The nozzle does not cool to the specified standby temp after the pause. It stays at the printing temp and of course makes a mess.

Share this post


Link to post
Share on other sites
Posted · New: Ultimaker Cura 3.5

I tried a lot with version 3.5.0 over the weekend. After I had deleted all definitions for material and printers many error messages are gone when starting the program.
The extremely slow speed doesn't change (mac osx 10.11.6). Every time I open a menu and it builds up very slowly the line "DEBUG - [MainThread] cura.AutoSave._onTimeout [48]: Autosaving preferences, instances and profiles" is displayed in stderr.log.
I have added the stderr.log to my file

 

++

ralf

stderr.log.zip

  • Like 1

Share this post


Link to post
Share on other sites
Posted · New: Ultimaker Cura 3.5

MORE BUGS - Supports

 

So again there are some very wrong stuff going on. Now printing supports where it is not sliced..

 

20181008_181548.thumb.jpg.8e5847c487103113fe8a6a9b6a585cd7.jpg20181008_182006.thumb.jpg.2fa71ec7fc3d3788777df1bc6fe2c81e.jpg

Share this post


Link to post
Share on other sites
Posted · New: Ultimaker Cura 3.5
On 10/5/2018 at 2:40 AM, lfei said:

 

Hi @James777, could you send us your cura configuration directory? It's in your user directory "C:\Users\<your-user-name>\AppData\Roaming\cura". Thanks in advance.

 

I was out of town for a bit, but I am back now. Here is the cura directory with both versions.

 

As i mentioned before; I did try to copy the definitions from 3.4.1 to 3.5.0. That is why there is a backup of the original 3.5.0 directory. I did this trick to copy my settings from my laptop to my desktop installations of cura a few weeks back which worked great. I thought it might work for 3.5.0.

 

 

cura James777.zip

Share this post


Link to post
Share on other sites
Posted · New: Ultimaker Cura 3.5
On ‎10‎/‎5‎/‎2018 at 6:15 PM, jonnyplastic said:

Curs 3.5 is soooooo sloooooow on my core 2 duo iMac running El Cap. Tons of pinwheels in layer mode. I think I'll have to switch back to 3.4x until this gets ironed out.

Even 3.4 is sloow on a Mac if you are used to the speed of S3D...the UI is decent...but could be alot better...slicing though...that takes forever. Using Cura makes the coffe machine work hard as there is a lot of waiting involved ?

Share this post


Link to post
Share on other sites
Posted · New: Ultimaker Cura 3.5
10 hours ago, James777 said:

 

I was out of town for a bit, but I am back now. Here is the cura directory with both versions.

 

As i mentioned before; I did try to copy the definitions from 3.4.1 to 3.5.0. That is why there is a backup of the original 3.5.0 directory. I did this trick to copy my settings from my laptop to my desktop installations of cura a few weeks back which worked great. I thought it might work for 3.5.0.

 

 

cura James777.zip

 

Hi @James777, thanks for the files, but unfortunately they are not the data files... Looks like they are the files in your "C:\Users\<your-user-name>\AppData\Local\cura". Could you check and send the files in "AppData\Roaming\cura"? Thanks again.

 

Share this post


Link to post
Share on other sites
Posted · New: Ultimaker Cura 3.5

Hi all,

 

FYI, we have found that cause of material diameter problem on Creality Ender 3 in Cura 3.5, which by default will be 2.85mm instead of 1.75mm. For developers, the JIRA ticket for this problem is CURA-5806.

Share this post


Link to post
Share on other sites
Posted · New: Ultimaker Cura 3.5
45 minutes ago, lfei said:

Hi all,

 

FYI, we have found that cause of material diameter problem on Creality Ender 3 in Cura 3.5, which by default will be 2.85mm instead of 1.75mm. For developers, the JIRA ticket for this problem is CURA-5806.

 

I tried to change the diameter to 1.75 manually. When I go to check the settings it still says the diameter is set to 1.75 but when I print it is still underextruding extremely much so apparently it doesn't change the setting where it matters.

 

Also, when I hit "print" the temperature always jumps to 210 degrees eventhough I have sliced it with a 190 degree setting.

 

All this is on Marlin firmware and Cure 3.5.
Cura version 3.4.1 works without a problem on the same model and settings.

Share this post


Link to post
Share on other sites
Posted · New: Ultimaker Cura 3.5

3.5 seems to "work" fine for me, but it will crash every 20-30 minutes or so. No error or anything, it just closes.

Share this post


Link to post
Share on other sites
Posted · New: Ultimaker Cura 3.5
13 hours ago, lfei said:

 

Hi @James777, thanks for the files, but unfortunately they are not the data files... Looks like they are the files in your "C:\Users\<your-user-name>\AppData\Local\cura". Could you check and send the files in "AppData\Roaming\cura"? Thanks again.

 

Yeah, must of mixed it up. Here's the other directory.

Roaming.cura.James777.zip

Share this post


Link to post
Share on other sites
Posted (edited) · New: Ultimaker Cura 3.5

To me the only slowdown is when opening cura, it needs more than 30 seconds even with a good PC and an SSD. Well, leaving alone the tree supports generation.

Edited by redslifer

Share this post


Link to post
Share on other sites
Posted · New: Ultimaker Cura 3.5
7 hours ago, James777 said:

Yeah, must of mixed it up. Here's the other directory.

Roaming.cura.James777.zip

 

Hi @James777, no sure what happened, but in the 3.5 folder, your custom qualities are indeed missing. I tried removing the 3.5 folder and then start Cura 3.5, which will upgrade using your existing 3.4 folder, and that worked for me. Could you try that, too?

  1. Remove the following folders:
    • C:\Users\<your-user-name>\AppData\Roaming\cura\3.5
    • C:\Users\<your-user-name>\AppData\Local\cura\3.5
  2. Start Cura 3.5

Share this post


Link to post
Share on other sites
Posted · New: Ultimaker Cura 3.5

I'm having some trouble with Cura 3.5.

 

Since updating, I have discovered a memory leak that comes up sometimes while printing over the network.

 

My PC has 32gb of ram and no other programs were open during the spike, but all 32gb of ram were being used until I closed Cura.

 

Any advice on a fix?

Share this post


Link to post
Share on other sites
Posted · New: Ultimaker Cura 3.5

3.5 quits on start. Fresh install on OS X 10.9.5 (NIVIDA GeForce 9600 GT)

Going back to 3.4.1 is fine (with some limitations).

 

Share this post


Link to post
Share on other sites
Posted · New: Ultimaker Cura 3.5

We are work hard on a bug fix release. Please try and give us some feedback:

 

https://drive.google.com/drive/folders/0B5IvTu1iM1pNMnE5YnlwZUlRSUE?usp=sharing

  • Like 1

Share this post


Link to post
Share on other sites
Posted · New: Ultimaker Cura 3.5

The 3.5.1 beta works fine for me!

The problem with loading .stl files under Win10 from external drives is resolved.

Tested with a VeraCrypt partion and a normal USB stick. No crashes anymore.

 

 

 

  • Like 1

Share this post


Link to post
Share on other sites
Posted · New: Ultimaker Cura 3.5

Am I the only one who is still having below problem with Cura 3.5? 

 

Error_message_1.jpg.8851c4a7fa893788cfe4feffff8847d6.jpg

 

Error_message_2.jpg.cf0673a72230d4c0d29fc0ba0acc2234.jpg

 

 

I have Ultimaker 3 extended, and I am facing this problem since Cura 3.3.1. 

 

 

Currently i am using a fix, suggested by @WaldoPepper99 , on this post https://community.ultimaker.com/topic/23272-issue-with-cura-331/?do=findComment&comment=211986 

 

I thought, it will be solved by now. 

 

 

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×
×
  • Create New...

Important Information

Welcome to the Ultimaker Community of 3D printing experts. Visit the following links to read more about our Terms of Use or our Privacy Policy. Thank you!