Jump to content
Ultimaker Community of 3D Printing Experts

Recommended Posts

Posted · bigger extruder motor

hey 🙂 Was wondering, my extruders motors keep dying on my UM2+ after 6 months, happened to me 3 times already in 1.5 years... I switched to the bondtech extruder, but it apparently requires more torque... so the question is, how fat of a motor can I install on it ? like, how much power can the motherboard spare for the extruder motor ? Because I'm really tired of printing at 30mm/s and still getting under extrusion with PLA because of a flipping motor  😕  

 

Thanks ^^ 

 

 

  • Link to post
    Share on other sites
    Posted · bigger extruder motor

    Hey, well effectively, wasn't the extruder motor this time... should of double checked before 😕 So the problem is the gear on the extruder motor, the little one that drive the bigger one on the extruder itself, that is becomming rounded on the inside and slips on the axis... Do you know where I could find one ? Can't seem to find some on the internet

     

    Thanks 🙂 

  • Link to post
    Share on other sites
    Posted · bigger extruder motor

    You mean within the Bondtech extruder? Check with them if they have a replacement part for that.

    I think to remember they have a 3d model of their housing, then it would be possible to reprint it.
    But I would assume the resin 3d print is sturdier than a FDM print.

     

    And still I think that there is too much force on the extruder for some reason.
     

  • Link to post
    Share on other sites
    Posted · bigger extruder motor

    I also think that you have somewhere a problem, and this is not the extruder. So check carefully the advice from conny_g, otherwise, it will not help if you replace the gear, it will again wear out.

    • Like 1
    Link to post
    Share on other sites
    Posted · bigger extruder motor

    Hello, 

    Checked again, the extruder turns freely, the filament can run through no problems... And after taking a closer look at the gear, it is definetly the problem, when I put it on the motor and make the motor turn, I can hold the gear, without applying much force at all, and the motor still spins ! It just doesn't hold anymore... So there is to much force on the reducting gear, not the extruder, so strange ! 

     

    And just to be shure of what gear we are talking about, I did a little sketch, sorry for my terrible paint skills :') 

     

    Thanks a lot ! 

    Bad drawing.png

  • Link to post
    Share on other sites
    Posted · bigger extruder motor

    If the gear has a normal round hole without a flat part, then you have to position the set screw to this flat part. When tightened, the screw prevents the gear from spinning on the axis. 

  • Link to post
    Share on other sites
    Posted · bigger extruder motor
    2 hours ago, Smithy said:

    If the gear has a normal round hole without a flat part, then you have to position the set screw to this flat part. When tightened, the screw prevents the gear from spinning on the axis. 

     

    The geared motors are all press fit. The knurled ones on the UM2 had set screws, but the plastic gears are press fit. 

    @Carlito are you putting a lot of grease on the gears? Installation instructions on the upgrade kit call for a little grease, but it should really only be a very little amount. I've seen a few slipped gears, but it shouldn't be occurring at the rate you're reporting. I would check into the other areas conny_g and Smithy mentioned. Something is making it work too hard.

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • Startups, apply for the Forward AM Innovation Award!
        Are you a startup using 3D printing? Perhaps you should continue reading... 
         
        Together with BASF we are launching the Forward AM Innovation Award - the very first global contest for startups developing new applications with 3D printing!
         
        Why apply?
        The winning startup will receive €100,000 in goods and services*, along with coaching and marketing exposure from top-notch leaders in the industry.
         

         
        Who can apply?
        Your startup creates products using Additive Manufacturing, is less than 5 years old, and has less than 50 employees. We are looking for 3D printing applications with a strong focus on innovation, sustainability and scalability.
         
        Dental aligners, shoes, tools, automotive parts, music instruments, industrial tooling and molding, medical implants, sports equipment, toys, architecture, fashion, construction... all are welcome to join!
         
        Do you have an innovative, sustainable and scalable idea that leverages the unique possibilities of 3D printing? Then it is time to apply!
        More information can be found here.
         
        Applications close on March 28th, 2021
        * What does "in goods and services" mean?
        The winner will be able to pick any item from the overall product and service portfolio of the sponsors, e.g. printers, materials, consulting, software... Choose whatever you need to accelerate your startup.
         
          • Like
        • 0 replies
      • New here? Register your Ultimaker for free 3D printer onboarding course
        Hi,
         
        Often getting started is the most difficult part of any process. A good start sets you up for success and saves you time and energy that could be spent elsewhere. That is why we have a onboarding course ready for
        Ultimaker S5 Pro Bundle, Ultimaker S5, Ultimaker S3 Ultimaker 2+ Connect.   
        They're ready for you on the Ultimaker Academy platform. All you need to do to gain access is to register your product to gain free access. 
        Ready? Register your product here in just 60 seconds.
          • Like
        • 0 replies
    ×
    ×
    • Create New...