Jump to content
Zbyszko

Speed test vase-mode (ChangeAtZ question)

Recommended Posts

Posted · Speed test vase-mode (ChangeAtZ question)

I'm trying to print a "speed tower" in vase mode.  Want to adjust the print speed up every 5mm of the tower.  I used Cura's ChangeAtZ post-processing plug-in to change the print speed.  Unfortunately it has no effect and I suspect this is due to the fact that wall speed is a multiple of print speed.  Any way to work around this so I can print my tower?  Is there a way to change the print speed to wall print speed multiplier from 0.5 to 1 somewhere?  Thanks!

Share this post


Link to post
Share on other sites
Posted · Speed test vase-mode (ChangeAtZ question)

First of all realize that there is a minimum layer time feature.  I think it defaults maybe to 5 seconds per layer so that may be restricting the speed.  You can turn that feature off.  This keeps the quality up because it looks all melty if you don't let the previous layer cool a little.

 

Cura has gotten complicated.  There are about 8 printing speeds.  I would try a few things:

1) Try setting most of them to 0.  In the old cura (15.X.X) if you set the speed to 0 it would just not set the speed at all. 

2) Open the gcode file in a text editor.  It's quite easy to look at.  Look for "F" commands.  Those set the speed in mm/minute (60X larger than mm/sec).  Note that anytime it does a non printing move it has to change the speed.  Note that anytime it does a retraction it has to change the speed (extruder speed is different from XY axis speed).  So you may have to disable all retractions and set the non-printing moves to speed 0 or to the same speed as the printing speed?  Not sure.  Hopefully in vase mode there are none of these.

 

Share this post


Link to post
Share on other sites
Posted · Speed test vase-mode (ChangeAtZ question)

Doesn't ChangeZ alter the feedrate factor instead of the "speed" itself? So it affects all the "speed" with a ratio. 

Could you look at if the output gcode has M220 in it? 

If there is, please check if your firmware has M220 support.

 

Share this post


Link to post
Share on other sites
Posted (edited) · Speed test vase-mode (ChangeAtZ question)
On 2/17/2019 at 8:58 AM, alexjx said:
On 2/16/2019 at 9:19 AM, gr5 said:

First of all realize that there is a minimum layer time feature.  I think it defaults maybe to 5 seconds per layer so that may be restricting the speed.  You can turn that feature off.  This keeps the quality up because it looks all melty if you don't let the previous layer cool a little.

 

Cura has gotten complicated.  There are about 8 printing speeds.  I would try a few things:

1) Try setting most of them to 0.  In the old cura (15.X.X) if you set the speed to 0 it would just not set the speed at all. 

2) Open the gcode file in a text editor.  It's quite easy to look at.  Look for "F" commands.  Those set the speed in mm/minute (60X larger than mm/sec).  Note that anytime it does a non printing move it has to change the speed.  Note that anytime it does a retraction it has to change the speed (extruder speed is different from XY axis speed).  So you may have to disable all retractions and set the non-printing moves to speed 0 or to the same speed as the printing speed?  Not sure.  Hopefully in vase mode there are none of these.

 

 

Thanks for taking the time to reply.  I did have min layer time turned to 0.  I did check the F commands and all layers were the same.  No retractions since printing in vase mode.  

 

Quote
On 2/17/2019 at 8:58 AM, alexjx said:

Doesn't ChangeZ alter the feedrate factor instead of the "speed" itself? So it affects all the "speed" with a ratio. 

Could you look at if the output gcode has M220 in it? 

If there is, please check if your firmware has M220 support.

 

 

 

 

You are correct.  Firmware is Repetier 1.0x which I believe does have M220 support.  I did try printing the square tower using manual feedrate control on the printer itself which worked but I learned that the printer doesn't like to take corners at a high speed (they show significant degradation beyond 40mm/s) so for this test I think I need to switch to a cylinder tower.

 

Still would like to know how to do this automatically if anyone has any other input.  Much thanks!

Edited by Zbyszko

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Our picks

    • Ultimaker Cura | a new interface
      We're not only trying to always make Ultimaker Cura better with the usual new features and improvements we build, but we're also trying to make it more pleasant to operate. The interface was the focus for the upcoming release, from which we would already like to present you the first glance. 
        • Like
      • 181 replies
    • "Back To The Future" using Generative Design & Investment Casting
      Designing for light-weight parts is becoming more important, and I’m a firm believer in the need to produce lighter weight, less over-engineered parts for the future. This is for sustainability reasons because we need to be using less raw materials and, in things like transportation, it impacts the energy usage of the product during it’s service life.
        • Like
      • 12 replies
×
×
  • Create New...

Important Information

Welcome to the Ultimaker Community of 3D printing experts. Visit the following links to read more about our Terms of Use or our Privacy Policy. Thank you!