Jump to content
Ultimaker Community of 3D Printing Experts

Recommended Posts

Hi,

i've installed the second extruder and updated my firmare. both hotends heat up and both extruder motors are working.

also added these changes in cura, head offset calibration is working.

but now when i'm opening 2 stl files and merge them for dual (in normal view theyre shown correctly) cura is not using the 2nd extruder. in gcode view theres only the toolpath for the first, toolpath for the 2nd is completely missing...

 

  • Link to post
    Share on other sites

    am i the only one unable to dual extrue in cura 13.06.04 ?

    it's working ith slic3r but print quality is not even near to cura :/

     

    It's working with me... I'm using a Ulticontroller, for one or another reason my 13.06.04 doesn.t work with the usb cable.

    I have a lot of experimenting and adjusting to do, but it prints 2 colors :)

     

  • Link to post
    Share on other sites

    Hard to tell from the pictures, you have to be sure that the 2 different stl, one for each color, have the same origin.

    I would think something is wrong with the model perhaps?

    Have you made the model yourself or downloaded it?

    If I had to draw something like this.

    I use autodesk 123D, but should work the same in most programs.

    Draw one box, split it a few times. Don't move physically anything.

    make 2 new empty parts and move, in your structure browser, the boxes by color.

    Save the parts by color in 2 seperate stl files.

    Open them together in cura and merge with the right mouse button.

    That's how it should work . :???:

     

  • Link to post
    Share on other sites

    downloaded it from thingiverse

    http://www.thingiverse.com/thing:12069

    i was able to print it with cura 12.12 and slic3r but in poor quality, 13.06.04 just puts out gcode for the 1st extruder ( but 2nd is heated up)

     

  • Link to post
    Share on other sites

    I'm printing it now, and it works, see if I can upload my gcode somewhere, perhaps that might help you to figure it out,

    I've put the code on my own webspace somewhere, pain in the a** to upload something here.

    http://3dcase.eu/cube4.gcode

    perhaps it helps..

     

  • Link to post
    Share on other sites

    found it ! In the extruder 2 offset settings cura doenst accept negative values!

    but this leads to the problem my 2nd extruder is left of the 1st in x direction :/

     

  • Link to post
    Share on other sites

    Nice! at least you van start printing :).

    Glad mine is +0.3

    I'm figuring out for myself how to make the printhead more sturdy, it's a little bit "wackelig" now.

    It can hit the the 2 rear platform levelling screws, or something curled up from the lower layer and then you can start all over again.

     

  • Link to post
    Share on other sites

    SOLVED!

    I've set the 2nd extruder offset to zero in cura settings an added the offsets manually to the start2 gcode

    its just 2 lines :

    M218 T0 X0 Y0 ;sets head offset

    M218 T1 X-21.6 Y0 ;sets head offset

     

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • Ultimaker turns 10: A look back
        Ultimaker is turning 10 years old and that means it is story telling time! We'll explore 2010-2014, traveling through the evolution of the business from the Protobox and Ultimaker Original, to the major leaps forward with the Ultimaker 2 and Ultimaker 3.
          • Like
        • 0 replies
      • Ultimaker Transformation Summit
        Visit our virtual showroom and learn more about the Ultimaker ecosystem!
        • 14 replies
      • New here? Register your Ultimaker for free 3D printer onboarding course
        Hi,
         
        Often getting started is the most difficult part of any process. A good start sets you up for success and saves you time and energy that could be spent elsewhere. That is why we have a onboarding course ready for
        Ultimaker S5 Pro Bundle, Ultimaker S5, Ultimaker S3 Ultimaker 2+ Connect.   
        They're ready for you on the Ultimaker Academy platform. All you need to do to gain access is to register your product to gain free access. 
        Ready? Register your product here in just 60 seconds.
          • Like
        • 4 replies
    ×
    ×
    • Create New...