Jump to content
Ultimaker Community of 3D Printing Experts

PLA filament breaks during cold pull


Recommended Posts

Posted · PLA filament breaks during cold pull

Hi Everyone,

 

I am trying to clean the print cores in my Ultimaker 3 using the standard procedure of hot and cold pulls, however, I am consistently breaking the PLA filament during the cold pull such that a large piece of it is still stuck in the print core. 

 

Any tips or suggestions for cleaning or how to overcome this?

 

Thanks!

 

Logan

  • Link to post
    Share on other sites
    Posted · PLA filament breaks during cold pull

    The last meter of PLA on a spool is often brittle - particularly if it was left in the bowden overnight.  Just break the brittle part off and throw it away.

     

    To get the filament out of the core it's easiest to just push it through while at 200C with another piece of filament (easier to go forwards than back).

     

    Alternatively you can heat a small exacto blade with a flame and then quickly slice off the filament just above the "trumpet" part of the core and now you can slide the core out.

     

    But then you still probably want to push the rest through anyway.

  • Link to post
    Share on other sites
    Posted · PLA filament breaks during cold pull

    I do a way more gentle pull than the traditional brutal cold pullings. Maybe this could help?

     

    - Manuall put print head in a front corner

    - Heat up nozzle (with bowden tube removed)

    - Push through some filament

    - Dial temp down to zero

    - Stop pushing filament, do a slight "manual retraction" of a few mm

    - Let cool down until nozzle is at room temp (25°C or less), so that the inner core of the filament also cools down well

    - If you have oil-free compressed air from a compressor, you can blow onto the nozzle to cool faster (but never use "air" from spray cans: this is often very explosive gas, and you don't want that on a hot nozzle)

    - When cold, gently try to rotate and wiggle the filament

    - Heat the nozzle to 70°C (for PLA, other materials need other temps)

    - While it is heating up, gently keep wiggling and rotating the filament until it comes out

     

    - Repeat as required.

     

    This method requires almost no force, but in my experience cleans as well as the original brutal cold pullings.

     

    The deeper cooling cycle to room temp is to totally solidify the inner core of filament. So, when heating up again, only the outside is molten, but the inner core stays strong and solid. The gentle pulling prevents damage to the nozzle, displacement of the coupler, and bending of the rods. It should also prevent breaking the filament.

     

    More info and pictures here (scroll down a bit):

    https://www.uantwerpen.be/nl/personeel/geert-keteleer/manuals/

     

    • Like 1
    Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • Ultimaker Transformation Summit

        On April 20 - April 23 we will host the Ultimaker Transformation Summit. Come talk to us via Live chat and get inspired by any of our relevant presentations!
        • 5 replies
      • New here? Register your Ultimaker for free 3D printer onboarding course
        Hi,
         
        Often getting started is the most difficult part of any process. A good start sets you up for success and saves you time and energy that could be spent elsewhere. That is why we have a onboarding course ready for
        Ultimaker S5 Pro Bundle, Ultimaker S5, Ultimaker S3 Ultimaker 2+ Connect.   
        They're ready for you on the Ultimaker Academy platform. All you need to do to gain access is to register your product to gain free access. 
        Ready? Register your product here in just 60 seconds.
          • Like
        • 0 replies
    ×
    ×
    • Create New...