Jump to content
xDmSx

Cura generated g-code produce stuttering on inner walls

Recommended Posts

Posted (edited) · Cura generated g-code produce stuttering on inner walls

Cura generated g-code produce stuttering on inner walls of cylinder with 3 perimeter walls. No stuttering in Slic3r with same parameters. Wall order optimization have no impact. Linear and less curvy objects don't have this problem objects.

Printer: Anet A6 (TATARA frame)

Video #1

Video #2

 

DSC00082.JPG

Edited by xDmSx

Share this post


Link to post
Share on other sites
Posted · Cura generated g-code produce stuttering on inner walls

Hello @xDmSx, please save the project (File -> Save) and attach the .3mf file to this thread. Thanks.

Share this post


Link to post
Share on other sites
Posted · Cura generated g-code produce stuttering on inner walls

Oh, and can you also please attach the gcode file. Thanks.

Share this post


Link to post
Share on other sites
Posted · Cura generated g-code produce stuttering on inner walls

I don't know if Cura is to blame (so topic might not be relevant). Downloaded CraftWare and it produced similar result (Have not much experience with it) . But Slic3r still make no problems. Just can't understand why outer walls are fine and inner stutter even with same speed-acceleration  settings. 
I uploaded some different project. It has same speeds for walls, but still stutter near smaller radius.

EllipseBench v1.3mf EllipseBench v1.gcode

Share this post


Link to post
Share on other sites
Posted · Cura generated g-code produce stuttering on inner walls

Hello @xDmSx, I suggest that you enable the Optimize Wall Printing Order setting (if not already enabled) and also set Minimum Wall Flow to something like 20.

Share this post


Link to post
Share on other sites
Posted · Cura generated g-code produce stuttering on inner walls

I don't know why under-extrusion occurs. Now I just wondering why inner wall prints with noticeable stutter, while outer walls smoothly with same speed-accel-jerk settings.

Share this post


Link to post
Share on other sites
Posted · Cura generated g-code produce stuttering on inner walls

When starting a new layer, sometimes it skips 1 thread. And that causes the layer skips as shown. Slicer and older Cura (before 3,6) does not make these things..

20190430_155921.jpg

20190505_080146.jpg

20190505_082339.jpg

20190505_082918.jpg

IMG-20190504-WA0022.jpg

Share this post


Link to post
Share on other sites
Posted (edited) · Cura generated g-code produce stuttering on inner walls

 

I think under-extruded lines happens in my "ring bench" because of pressure drop and leaking of some filament during strange move nozzle make above already printed inner wall area. If I set Z-seam to be at one position (not random) it can be clearly seen. Under-extruded lines right at outer wall start, not at layer change!

I have 0.6mm nozzle, and ring wall is 1.8mm. Cura 3.6. Same with version 4.0.

Look at simulation video. You can see nozzle moves around green line 2 times - 1 when printing and 1 when travel to start of outer (red) wall! But speed is same, not as travel (I can see it while printing), so is it not a travel move?

Whichever settings I change I can't get rid of this useless move. e.g. Combing, Line Width, Do not print thin walls etc.

 

DSC00085.JPG

Edited by xDmSx

Share this post


Link to post
Share on other sites
Posted · Cura generated g-code produce stuttering on inner walls
On 5/14/2019 at 1:02 PM, burtoogle said:

Hello @xDmSx, I suggest that you enable the Optimize Wall Printing Order setting (if not already enabled) and also set Minimum Wall Flow to something like 20.

 

@xDmSx, two days ago, I suggested that you set the Min Wall Flow to a lowish value. Did you try that? I think it solves the problem of printing walls that are an odd number of lines thick.

  • Like 1

Share this post


Link to post
Share on other sites
Posted · Cura generated g-code produce stuttering on inner walls

Sorry, my mistake it needs to be a higher value than that, probably 50 would be OK.

 

  • Like 1

Share this post


Link to post
Share on other sites
Posted (edited) · Cura generated g-code produce stuttering on inner walls

Thank you, @burtoogle. That thing worked. And now pipe came out with acceptable quality without much holes in shell 😊, just needs some little tweaks. Additional movement over inner wall was removed. Haven't notice these parameter before.

 

But my original problem was jerky movement on inner wall and it still remains, but not produce major impact on print quality now.

So I will leave it as it is for now.

Edited by xDmSx

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Our picks

    • Ultimaker Cura 4.0 | Stable available!
      Ultimaker Cura 4.0 is mainly focused on the improved user interface and cloud integration.
      As always, we want to collect your user feedback for this release. If there are any improvements you can think of, feel free to mention it here and help us to shape the next release.
      • 96 replies
×
×
  • Create New...

Important Information

Welcome to the Ultimaker Community of 3D printing experts. Visit the following links to read more about our Terms of Use or our Privacy Policy. Thank you!