Jump to content

Recommended Posts

Posted · Fuel3D Scanify Error Engine_040

Hello everyone,

 

I have a fuel3D Scanify 3D Scanner. But program doesn't work. Error Message:

 

"Error running engine 'Engine_040' status 262149"

 

So how can I fix this error? can i use another program?

 

Thank you 

Onur

222.png

Share this post


Link to post
Share on other sites
Posted · Fuel3D Scanify Error Engine_040

ahhh, I have one but didn't use it for ages...

 

I just downloaded the software, and entered the licence code from here;

https://www.fuel3d.com/scanify-closure-notice/

 

I installed on Win10 and it accepted the code, and started without error.

I have not tried a scan jet, but probably give it a spin tomorrow.

 

At what point did you get the error?

Share this post


Link to post
Share on other sites
Posted · Fuel3D Scanify Error Engine_040

Hi ultiarjan,

 

I'm scanning then I confirm and I get this error. I can never use this product. I updated the graphic driver and other driver. I use win10 but  I can never use this product.

 

what should i do..??

Share this post


Link to post
Share on other sites
Posted · Fuel3D Scanify Error Engine_040

Ok, thanks to you I dusted of this thing I had almost forgotten about, and of which I'm pretty sure it's the nr.1 waste of money in my life 🙂

 

though I did get it to work, it's more or less unusable, during scanning it somewhat randomly will scan or not, It's almost impossible to move the scanner to the tiny distance window where it will scan.

Also the result is crap....

fuel.thumb.png.a5b00ffada3113ca2c2d9c5e11f6fbf0.png

 

To get 3 scans I had multiple errors, and needed to reboot the software once...

 

just a few examples..

F1.png.25b3ab738b6e68892586e02a2a27ae1a.png

f2.png.e5709b8fb8462c16a6c628a70b2bfb04.png

F3.png.559945580651717d44bf36b1fb9d4f31.png

 

I did not look into the option of using the device with other software jet, but it's clear trying to work with the unsupported old software is useless....

 

Think I'll put it back in a box and try to forget about it again....

 

 

 

 

 

Share this post


Link to post
Share on other sites
Posted · Fuel3D Scanify Error Engine_040

aahahhahaa  I agree with you, 1 waste of money in my life 🙂

 

I sent the company an e-mail. No one has written an answer yet. The product is very new but I can not use it at all. hope i can find a solution. if i solve the problem i will share. please wish me luck 🙂

Share this post


Link to post
Share on other sites
Posted · Fuel3D Scanify Error Engine_040

I have the exact same Problem with the 3D-Scanner/Software.

"Error running engine 'Engine_040' status 262149"

Tried the latest software from their website (Studio 2.2 64bit) on

- Windows 7
- Windows 8.1
- Windows 10

all on different machines.

Always the same error.

Additionally I saw, that on my Scanner the only LED on the backside who is lit, is the right blue one.
All other shown no activity. In the manual is stated, that they will lit depending on the
action (start Viewfinder, move farer/closer to the scanning object, Flash is reloading and so on).

Unfortunally their download link to the older 2.1 Studio (32bit) on their site is down.
(https://fuel-3d.box.com/v/Win32bit)

I would like to try this software/driver. Can anyone send me a (link to a) copy?

At the end, i assume that the Scanner has a hardware failure.
 

Share this post


Link to post
Share on other sites
Posted · Fuel3D Scanify Error Engine_040

I'm going through the same issue with trying to find the 32 bit download of the 2.1 software, if you find a copy please let me know! I've been emailing support with no response =\

Share this post


Link to post
Share on other sites
Posted (edited) · Fuel3D Scanify Error Engine_040
9 hours ago, Jayjayn said:

I'm going through the same issue with trying to find the 32 bit download of the 2.1 software, if you find a copy please let me know! I've been emailing support with no response =\

 

Hi,

 

i already returned the device, as i got no feedback from here or from the (former) Fuel3D support.

 

I assume that the device has a hardware and not a software problem (calibration).

 

In the meanwhile i switched to structured light scanning and i'am very impressed with the results (of course SLS comes not as cheap as the Fuel3D solution). 

 

I will leave a comment here if i get news about the 32bit software.

 

Good luck!

Edited by 3dmurx

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×
×
  • Create New...

Important Information

Welcome to the Ultimaker Community of 3D printing experts. Visit the following links to read more about our Terms of Use or our Privacy Policy. Thank you!