Jump to content

S5 core seems to be clogged but isn't


Recommended Posts

Posted · S5 core seems to be clogged but isn't

Hi!

 

I have a reoccuring problem with multiple of my S5 printers. At first, it seemed that the core was clogged, no material extruded. After cleaning the same problem occured. I checked the feeder and feeder tension. During the material change, material extrudes normally trough the nozzle, but with the first layer, lines get thinner and thinner until no material extrudes and a notification for 'material empty' pops up. It seems that the feeder tries to 'jam' the material into the print core what results in a thickened wire (which makes it harder to pull it out of the core or to change material.

 

Does anyone experienced similar problems and/or know a solution to this problem?

 

 

  • Like 1
Link to post
Share on other sites

Posted · S5 core seems to be clogged but isn't

Which firmware do you have on your S5?

There is/was a bug that the filament is retracted too far after a print and then the print starts without extruding. It helps when you push the filament manually forward at the start of your print. Or install the latest firmware which is actually a step back to the previous one.

  • Link to post
    Share on other sites

    Posted · S5 core seems to be clogged but isn't
    On 10/25/2019 at 8:40 AM, MichielJacobi said:

    It seems that the feeder tries to 'jam' the material into the print core what results in a thickened wire (which makes it harder to pull it out of the core or to change material.

     

    Does anyone experienced similar problems and/or know a solution to this problem?

     

     

     

    I suffered exactly from this (UM3), the front fan was dead.

     

    Didnt notice at first since side cooling fans and the one to my HEPA filter was running. 

  • Link to post
    Share on other sites

    Posted · S5 core seems to be clogged but isn't

    If the front fan is dead, like @AndersK mentioned, it would explain all of your problems.

    Is the jam happening with both of the printcores?

     

    Check the connector on the back of the printhead and check if is is in place propperly, press it down and wiggle it a little (you dont want to break the connector). Then heat a printcore to about 100 degrees (at this point the front fan should definally be spinning), if the front fan still isn't moving, it is probably dead and needs replacement.

  • Link to post
    Share on other sites

    Posted (edited) · S5 core seems to be clogged but isn't

    Checked & cleaned the fan, seems to have solved the problem. 

    Edited by MichielJacobi
    • Like 1
    Link to post
    Share on other sites

    Posted · S5 core seems to be clogged but isn't

    What was the issue?

    Was the fan jammed with some filament stringing or was the connector not propperly connected?

    • Like 1
    Link to post
    Share on other sites

    Posted · S5 core seems to be clogged but isn't
    On 10/31/2019 at 4:46 PM, TheodorK said:

    What was the issue?

    Was the fan jammed with some filament stringing or was the connector not propperly connected?

    this was exactly my issue.. i will install a fine mesh there.  my nozzle is now clogged/dead..  cant move the stump of filament in there.. hot or cold.  
    does anyone have a walk-trough for disassembling and cleaning a S5 nozzle.  

  • Link to post
    Share on other sites

    Posted · S5 core seems to be clogged but isn't

    I don't recommend to disassemble the print core, it can break easily and even if you can disassemble it, it is hard to get a tight fit again. I would try to heat up the core, open the front door that the fan cannot cool the hot end and try if you can pull out the filament. If you cannot reach something from the top of the core, try it with a needle or a thin wire trough the nozzle.

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • Introducing Universal Cura Projects in the UltiMaker Cura 5.7 beta
        Strap in for the first Cura release of 2024! This 5.7 beta release brings new material profiles as well as cloud printing for Method series printers, and introduces a powerful new way of sharing print settings using printer-agnostic project files! Also, if you want to download the cute dinosaur card holder featured below, it was specially designed for this release and can be found on Thingiverse! 
          • Like
        • 10 replies
      • S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
        (Sorry, was out of office when this released)

        This update is for...
        All UltiMaker S series  
        New features
         
        Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
          • Like
        • 0 replies
    ×
    ×
    • Create New...