Jump to content

Recommended Posts

Posted · Cura Slices are rebooting my printer

I installed several plugins and have messed with so many settings I have no idea which one is causing me problems but every time I try to print anything newly sliced I get an Error:No Checksum with line number, Last Line: 37
Recv: Resend: 38 

and the printer reboots.  Here is my log info if anyone can help I would be very grateful. Thanks

 

 

Send: N29 G1 X1.2 Y200.0 Z0.3 F5000.0*57
Recv:  T:249.48 /250.00 B:79.98 /80.00 @:56 B@:86
Recv: echo:busy: processing
Recv:  T:249.41 /250.00 B:79.92 /80.00 @:58 B@:110
Recv: echo:busy: processing
Recv: ok
Send: N30 G1 X1.2 Y20 Z0.3 F1500.0 E30*120
Recv:  T:249.48 /250.00 B:79.88 /80.00 @:55 B@:124
Recv: ok
Send: N31 G92 E0*117
Recv:  T:249.68 /250.00 B:80.03 /80.00 @:51 B@:76
Recv: echo:busy: processing
Recv:  T:249.82 /250.00 B:80.20 /80.00 @:50 B@:17
Recv: echo:busy: processing
Recv:  T:250.37 /250.00 B:80.13 /80.00 @:35 B@:37
Recv: echo:busy: processing
Recv: ok
Send: N32 M117 Bad accuracy*79
Recv: X:1.20 Y:20.00 Z:0.30 E:0.00 Count X:120 Y:8995 Z:94
Recv: ok
Recv: ok
Send: N33 G1 Z1.0 F3000*40
Send: N34 M117 Autobots! Roll Out!*101
Recv: ok
Send: N35 G92 E0*113
Recv: ok
Send: N36 G92 E0*114
Recv: X:1.20 Y:20.00 Z:1.00 E:0.00 Count X:120 Y:8443 Z:94
Recv: ok
Send: N37 G1 F3600 E-7*0
Recv: X:1.20 Y:20.00 Z:1.00 E:0.00 Count X:120 Y:8415 Z:94
Recv: ok
Send: N38 M117 Printing ANETA6_Titan_Aero_X_Carrier_for_Anet_A6_-_V2 - Layer 0 ANETA6_Titan_Aero_X_Carrier_for_Anet_A6_-_V2 of 274*72
Recv: Error:No Checksum with line number, Last Line: 37
Recv: Resend: 38
Recv: ok
Send: N38 M117 Printing ANETA6_Titan_Aero_X_Carrier_for_Anet_A6_-_V2 - Layer 0 ANETA6_Titan_Aero_X_Carrier_for_Anet_A6_-_V2 of 274*72
Recv: Error:No Checksum with line number, Last Line: 37
Recv: Resend: 38
Recv: ok
Send: N38 M117 Printing ANETA6_Titan_Aero_X_Carrier_for_Anet_A6_-_V2 - Layer 0 ANETA6_Titan_Aero_X_Carrier_for_Anet_A6_-_V2 of 274*72
Recv: Error:No Checksum with line number, Last Line: 37
Recv: Resend: 38
Recv: ok
Send: N38 M117 Printing ANETA6_Titan_Aero_X_Carrier_for_Anet_A6_-_V2 - Layer 0 ANETA6_Titan_Aero_X_Carrier_for_Anet_A6_-_V2 of 274*72
Recv: Error:No Checksum with line number, Last Line: 37
Recv: Resend: 38
Recv: ok
Send: N38 M117 Printing ANETA6_Titan_Aero_X_Carrier_for_Anet_A6_-_V2 - Layer 0 ANETA6_Titan_Aero_X_Carrier_for_Anet_A6_-_V2 of 274*72
Recv: ok
Send: N39 M107*31
Recv: Error:No Checksum with line number, Last Line: 37
Recv: Resend: 38
Recv: ok
Send: N38 M117 Printing ANETA6_Titan_Aero_X_Carrier_for_Anet_A6_-_V2 - Layer 0 ANETA6_Titan_Aero_X_Carrier_for_Anet_A6_-_V2 of 274*72
Recv: Error:No Checksum with line number, Last Line: 37
Recv: Resend: 38
Recv: ok
Send: N39 M107*31
Recv: Error:Line Number is not Last Line Number+1, Last Line: 37
Recv: Resend: 38
Recv: ok
Send: N38 M117 Printing ANETA6_Titan_Aero_X_Carrier_for_Anet_A6_-_V2 - Layer 0 ANETA6_Titan_Aero_X_Carrier_for_Anet_A6_-_V2 of 274*72
Recv: Error:No Checksum with line number, Last Line: 37
Recv: Resend: 38
Recv: ok
Send: N39 M107*31
Recv: Error:Line Number is not Last Line Number+1, Last Line: 37
Recv: Resend: 38
Recv: ok
Send: N38 M117 Printing ANETA6_Titan_Aero_X_Carrier_for_Anet_A6_-_V2 - Layer 0 ANETA6_Titan_Aero_X_Carrier_for_Anet_A6_-_V2 of 274*72
Recv: Error:No Checksum with line number, Last Line: 37
Recv: Resend: 38
Recv: ok
Send: N39 M107*31
Recv: Error:Line Number is not Last Line Number+1, Last Line: 37
Recv: Resend: 38
Recv: ok
Send: N38 M117 Printing ANETA6_Titan_Aero_X_Carrier_for_Anet_A6_-_V2 - Layer 0 ANETA6_Titan_Aero_X_Carrier_for_Anet_A6_-_V2 of 274*72
Recv: Error:No Checksum with line number, Last Line: 37
Recv: Resend: 38
Recv: ok
Send: N39 M107*31
Recv: Error:Line Number is not Last Line Number+1, Last Line: 37
Recv: Resend: 38
Recv: ok
Send: N38 M117 Printing ANETA6_Titan_Aero_X_Carrier_for_Anet_A6_-_V2 - Layer 0 ANETA6_Titan_Aero_X_Carrier_for_Anet_A6_-_V2 of 274*72
Recv:  T:250.37 /250.00 B:80.05 /80.00 @:36 B@:61
Recv: Error:No Checksum with line number, Last Line: 37
Recv: Resend: 38
Recv: ok
Send: N39 M107*31
Recv: Error:Line Number is not Last Line Number+1, Last Line: 37
Recv: Resend: 38
Recv: ok
Send: N38 M117 Printing ANETA6_Titan_Aero_X_Carrier_for_Anet_A6_-_V2 - Layer 0 ANETA6_Titan_Aero_X_Carrier_for_Anet_A6_-_V2 of 274*72
Recv: Error:No Checksum with line number, Last Line: 37
Recv: Resend: 38
Recv: ok
Send: N39 M107*31
Recv: Error:Line Number is not Last Line Number+1, Last Line: 37
Recv: Resend: 38
Printer keeps requesting line 38 again and again, communication stuck
Changing monitoring state from "Printing" to "Error: Printer keeps requesting line 38 again and again, communication stuck"
Send: M112
Send: N40 M112*21
Send: N41 M104 T0 S0*20
Send: N42 M140 S0*83
Changing monitoring state from "Error: Printer keeps requesting line 38 again and again, communication stuck" to "Offline (Error: Printer keeps requesting line 38 again and again, communication stuck)"
Connection closed, closing down monitor
Closing down send loop

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • Help Us Improve Cura – Join the Ultimaker Research Program
        🚀 Help Shape the Future of Cura and Digital Factory – Join Our Power User Research Program!
        We’re looking for active users of Cura and Digital Factory — across professional and educational use cases — to help us improve the next generation of our tools.
        Our Power User Research Program kicks off with a quick 15-minute interview to learn about your setup and workflows. If selected, you’ll be invited into a small group of users who get early access to features and help us shape the future of 3D printing software.

        🧪 What to Expect:
        A short 15-minute kickoff interview to help us get to know you If selected, bi-monthly research sessions (15–30 minutes) where we’ll test features, review workflows, or gather feedback Occasional invites to try out early prototypes or vote on upcoming improvements
        🎁 What You’ll Get:
         
        Selected participants receive a free 1-year Studio or Classroom license Early access to new features and tools A direct voice in what we build next
        👉 Interested? Please fill out this quick form
        Your feedback helps us make Cura Cloud more powerful, more intuitive, and more aligned with how you actually print and manage your workflow.
        Thanks for being part of the community,

        — The Ultimaker Software Team
        • 0 replies
      • Cura 5.10 stable released!
        The full stable release of Cura 5.10 has arrived, and it brings support for the new Ultimaker S8, as well as new materials and profiles for previously supported UltiMaker printers. Additionally, you can now control your models in Cura using a 3D SpaceMouse and more!
          • Like
        • 18 replies
    ×
    ×
    • Create New...