Jump to content
Ultimaker Community of 3D Printing Experts

How to print big cubical object without infill


Recommended Posts

Posted · How to print big cubical object without infill

Hello,

 I am totally new user of 3d printing ,  i need to print few large size objects like 500mm x 300 mm. one is cubical box contains embossed design from base and top. i want to print in two parts,  only shell, hollow without infill . so can someone please guide me is that possible ? if yess. what layers and shell setting shall I use ? I don't need super detailed. ci am thinking to use 0.6 or 0.8 mm nozzle to save print time too. 

  • Share this post


    Link to post
    Share on other sites
    Posted · How to print big cubical object without infill

    Set top thickness and infill density to 0. That will give you an open box with just bottom and walls.

     

    Layer settings and wall thickness is something you need to find out based on your requirements and printer quality.

     

    When I print concept models just for "show & tell" I ususally print with 0,3 layer height and 0,8 wall with 5-10 % infill.

    Models for use, like tools and parts for testing usually 0,1 mm layer height and 3 mm wall. 

     

     

    • Thanks 1

    Share this post


    Link to post
    Share on other sites
    Posted · How to print big cubical object without infill

    Thanks for your answer AndersK. I will set infill and top thickness to 0 density. I have few more questions regarding support. so I have attached pictures pf my models for that. my base surface of model is very uneven and have embossed pattern on it. Will it need support on bottom?. Also ropes shows a little red spots from lower side. if I put support it shows from bottom to robes. which cost a lot of filament and time. how can I reduce support to save filament and time ? does this another small plate object can be print without support too ?

     

    1593667596_Screenshot2020-01-22at11_28_31.thumb.png.fe276678c38e27dbbe80be7714330699.png1548268905_Screenshot2020-01-22at11_27_55.thumb.png.39debf3dfea4a44339798a3dd2a59e1e.png33054581_Screenshot2020-01-22at11_42_50.thumb.png.bd3b2433547f40162dde71b22eee89a7.png1918557810_Screenshot2020-01-22at11_30_41.thumb.png.bec4d47e561900382c10e8b746c861fb.png

  • Share this post


    Link to post
    Share on other sites
    Posted · How to print big cubical object without infill

    The red highlighted parts of the model mean that the area needs support material (as they exceed the minimum support overhang angle). So yes, it looks like the 'rope' sections and bottom section will require supports. Cura can place these automatically.

     

    If you want to use support more efficiently, you can use features such as conical support or gradual support.

     

    Hope this helps.

  • Share this post


    Link to post
    Share on other sites
    Posted (edited) · How to print big cubical object without infill

    You might get away with no support under the ropes since it looks like a really small area.

     

    Conical support is found under experimental and gradual under support section.

     

    Hint, use the "search setting" 

     

     

    Edit, might have misread your question. Both gradual and conical support is methods to reduce the amount of support material used, (and printing time at a small amount) by using less material at the bottom of the print and increasing it closer to he supported surfaces.

     

     

    image.png.8ffac40ec32056e3af13df81c99b4811.png

    Edited by AndersK
  • Share this post


    Link to post
    Share on other sites
    Posted · How to print big cubical object without infill

     

    Hi, I got Creality CR 10s Pro two weeks ago. I tested last week my first test print it was a good result. Today I changed nozzle into 0.8mm . After changing nozzle I am getting zhome issues. Printer extruder/nozzles goes high like 2/3 inches. doesn't come to the bed level. when I try to reset with levelling mode, z+ z-home doesn't work an doesn't not move -z or +z. I tried manual home by turn off motor. but when it start print extruder goes up again and starts printing in air. please help me

  • Share this post


    Link to post
    Share on other sites
    Posted · How to print big cubical object without infill

    I don't know those machines but if it started with a nozzle change I would change back to see if it changes goes back to normal.

  • Share this post


    Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • Talking additive | The 3D printing podcast
        Why should we be the only ones asking questions? Join us and ask Jabil all your questions on September 22nd 5pm CET
          • Like
        • 3 replies
      • Ultimaker masterclass: Optimizing your Ultimaker Cura workflow
        Save your seat for either broadcast on September 23.
        What will you learn?
        · Best practices for iterative print preparation and every lesson you should learn from each print
        · The right way to use per-object settings and when they are most useful
        · Easy-to-use resources for anyone who wants to develop their own printer definitions, plugins, or print profiles
        · How to optimize print profile settings and whether to “keep” or “discard” changes
        · When is the right time to export your drawing from CAD? (Based on Ultimaker Cura’s surprising power as 3D control software)
        · And a whole lot more tips and tricks!
         
        How can I join?
        This free masterclass will take place twice:
        1. 11am CEST (5pm SGT, 5am EDT)
        2. 5pm CEST (11am EDT, 8am PDT, 11pm SGT)
          • Like
        • 0 replies
      • Do you use 3D printing at work? Let us know
        It doesn't matter if you are using 1 Ultimaker or 10, there is inspiration in everything. We're looking for ...
        • 1 reply
    ×
    ×
    • Create New...