Jump to content
Ultimaker Community of 3D Printing Experts

Recommended Posts

Posted · 3DLac versus Magigoo

It's a matter of taste, you can basically use all these things and there will be no general statement about what is better.

 

For PLA I use either the normal Magigoo stick or normal glue stick. For nylon Magigoo has a special stick or Dimafix, which I have had good experience with.

 

I have also used 3DLac, which is more like a hairspray, but it also works quite well with ABS or PETG.

 

Mostly I use Magigoo, because it is easier to apply.

 

  • Link to post
    Share on other sites
    Posted · 3DLac versus Magigoo

    I was talking about the special Magigoo for Nylon. I hadn't realised that they did a common-and-garden version as well.

     

    I like 3DLac in that I find, personally, find it easier to apply than a stick. Mind you, I tend to stay away from the printer until the fumes have dispersed.

  • Link to post
    Share on other sites
    Posted · 3DLac versus Magigoo

    The rods and z-screw will get really sticky with time, so you should not do that inside the printer. 

    I bought some months ago an used UM2+ printer and the previous owner also used some spray for adhesion. Everything was really sticky and I needed several hours to clean everything. It was not easy to clean the things, so be careful.

  • Link to post
    Share on other sites
    Posted · 3DLac versus Magigoo

    Point taken. I've been using it for a year or so without obvious issues, but I see the danger. Thanks.

  • Link to post
    Share on other sites
    Posted · 3DLac versus Magigoo

    I don't know which printer you have, when it is not enclosed like the UM printers, then it could be less problematic when you are careful. 

  • Link to post
    Share on other sites
    Posted · 3DLac versus Magigoo

    Yep always take it out to spray, in time if you don't clean your rods from time to time you will find that the print head will start to stick when moving and make your prints fail. It can also get on the sensors if your printer as a light based homing sensor and stop them working.

  • Link to post
    Share on other sites
    Posted · 3DLac versus Magigoo

    I never used sprays for 3D-print adhesion.

     

    But years ago I did use a lot of silicone anti-stick sprays for moulding and casting models. I had built a special cardboard box with fume extraction at the back, to take away the spray mist. And I only sprayed deep into that box. But even then the whole area outside of that cardboard box got slippery with silicone oil too, after some time.

     

    I have seen similar setups where people used spray paints, and there too the whole environment got colored. Even though they had fume extraction in their cardboard box, just like me!

     

    If you are very adventurous, try using bright red paint instead of glue spray. And see where it goes. (No, don't do it.  :-)

     

  • Link to post
    Share on other sites
    Posted · 3DLac versus Magigoo
    On 3/1/2020 at 7:31 PM, Smithy said:

    Yes, Magigoo has a lot of different products, also for PP, PC,....

     

    I hope you take the build plate out of the printer when you apply the spray?


    Is much easier to apply the spray to a paper towel outside and rub it on the plate. Removes the bed alignment problem

     

    3DLac is basically Nely Strong hairspray 3€ (made by the same company under other name)

     

    Smartmaterials smartstick works even with PP but is quite a mess to remove (but sticks to everything I have try). Bed adhesion sheets made from PE by Avery ) a4 laser printable stickers) work really nice and with windowasher you can reuse them a lot tpe, tpu, just heat the bed to 35 to remove it slowly and not break it, ofc they break after 10-15 uses and is a mess to replace and remove the glue.

     

    That’s my 2 cents ;D

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • 18 Visiting our virtual showroom

      1. 1. Have you visited our virtual showroom before?


        • Yes
        • No
      2. 2. If yes - what content did you find most interesting?


        • Information about Ultimaker ecosystem
        • Applications & application stories
        • Customer success stories
        • Webinar sessions
        • Material wall & ecosystem partners
        • New product introduction; software subscription plans
      3. 3. What of the below would make you consider visiting (again)?


        • New Live Ultimaker Webinar streams
        • ‘Ask Me Anything’ with industry experts or Ultimaker staff via main stage and public chat
        • New customer success stories
        • New applications
        • Presentations/news from ecosystem partners
        • Opportunity to meet representatives for an interactive tour
        • Helpful videos like Software tutorials
        • Other; leave input in a comment below!

    • Our picks

      • Ultimaker turns 10: A look back
        Ultimaker is turning 10 years old and that means it is story telling time! We'll explore 2010-2014, traveling through the evolution of the business from the Protobox and Ultimaker Original, to the major leaps forward with the Ultimaker 2 and Ultimaker 3.
          • Like
        • 0 replies
      • Ultimaker Transformation Summit
        Visit our virtual showroom and learn more about the Ultimaker ecosystem!
        • 14 replies
      • New here? Register your Ultimaker for free 3D printer onboarding course
        Hi,
         
        Often getting started is the most difficult part of any process. A good start sets you up for success and saves you time and energy that could be spent elsewhere. That is why we have a onboarding course ready for
        Ultimaker S5 Pro Bundle, Ultimaker S5, Ultimaker S3 Ultimaker 2+ Connect.   
        They're ready for you on the Ultimaker Academy platform. All you need to do to gain access is to register your product to gain free access. 
        Ready? Register your product here in just 60 seconds.
          • Like
        • 0 replies
    ×
    ×
    • Create New...