Jump to content
Ultimaker Community of 3D Printing Experts

Infinite Material Solutions: Aquasys


Recommended Posts

Posted (edited) · Infinite Material Solutions: Aquasys

Hello,

I recently got this great (in theory) material that will print with my high temp nylon and can dissolve up to 6x faster than PVA. Since I have been using nylon I know the effects of moisture and dry them out before each trial but it seems I can never get the Aquasys dry enough. I continually have stringing and many problems with it not sticking to layers of itself or layers of the nylon. Again, really great product but am needing some more information on it.

Thanks, Will

Edited by willryan3
  • Link to post
    Share on other sites
    Posted · Infinite Material Solutions: Aquasys

    Hi @willryan3, thank you for your post. Good that you dry before you use it, that is important. Can you elaborate on how you dry it, and for how long approximately? Do you keep it stored in a dry environment, like in the Material Station, or a bag with silica packs? 

  • Link to post
    Share on other sites
    Posted · Infinite Material Solutions: Aquasys
    3 hours ago, SandervG said:

    Hi @willryan3, thank you for your post. Good that you dry before you use it, that is important. Can you elaborate on how you dry it, and for how long approximately? Do you keep it stored in a dry environment, like in the Material Station, or a bag with silica packs? 

    Thank you for your response. I have been using the PrintDry oven and heating at its' highest temp for 4 hours prior to a print with it. As far as storing I use the same bag it came in with a few silica packs. Would a material like this need to be concealed during the print also? My area for printing has a humidity between 20-30%.

    Thanks Will

  • Link to post
    Share on other sites
    • 11 months later...
    Posted · Infinite Material Solutions: Aquasys
    On 4/30/2020 at 8:49 AM, willryan3 said:

    Thank you for your response. I have been using the PrintDry oven and heating at its' highest temp for 4 hours prior to a print with it. As far as storing I use the same bag it came in with a few silica packs. Would a material like this need to be concealed during the print also? My area for printing has a humidity between 20-30%.

    Thanks Will

     Did you get better results ? I have the same issues with Aquasys and my printer (ultimaker S5 Pro Bundle). I wonder what we should change to get better prints. 

     

    Any Feedback ? @willryan3 @SandervG

  • Link to post
    Share on other sites
    Posted · Infinite Material Solutions: Aquasys
    On 4/13/2021 at 10:39 PM, Nicko_Airbus said:

     Did you get better results ? I have the same issues with Aquasys and my printer (ultimaker S5 Pro Bundle). I wonder what we should change to get better prints. 

     

    Any Feedback ? @willryan3 @SandervG

     

    Hi @Nicko_Airbus thank you for your message. Apologies for my late response. I was quite occupied with the organising and contributing during the Ultimaker Transformation Summit. Can you explain what issues you are experiencing, and can you elaborate a little bit more on how you use the material in combination with the material station?

     

    For example, do you dry it before it goes into the material station? It does a great job keeping it dry, but it might be more difficult in getting it dry if it contained too much moisture when you load it in the material station. 

  • Link to post
    Share on other sites
    Posted · Infinite Material Solutions: Aquasys

    Since the first time I received it (in a box and sealed bag (I think)) I put it in the material station. Every now and then, the filament brakes in the bodwen tube, sometimes It doesn't stick to the other layers and and some stringing.

     

    I just had the same problem with my ultimaker natural PVA. Printing .3mm high layers at 35 mm/s at 220C. Other settings are as suggested by cura...

  • Link to post
    Share on other sites
    Posted · Infinite Material Solutions: Aquasys
    On 4/29/2021 at 8:03 PM, Nicko_Airbus said:

    Every now and then, the filament brakes in the bodwen tube

     

    In the Bowden tube indeed? Not in the main feeder? What does your S5 show on the side panel, an Ultibot or the current Ultimaker logo (U)?

  • Link to post
    Share on other sites
    Posted · Infinite Material Solutions: Aquasys
    On 5/1/2021 at 7:51 AM, Dim3nsioneer said:

     

    In the Bowden tube indeed? Not in the main feeder? What does your S5 show on the side panel, an Ultibot or the current Ultimaker logo (U)?

     I don't know if it happens in the material station or in the bowden tube. I see the logo, not the robot

  • Link to post
    Share on other sites
    Posted · Infinite Material Solutions: Aquasys

    I'm having them same issue with aquasys in s5 pro bundle with robot on the side. it breaks in the bowden tube after the feeder.

  • Link to post
    Share on other sites
    Posted · Infinite Material Solutions: Aquasys

    Hi @Nicko_Airbus and @kevinmoore1337, thank you for your message. 

    I would like to ask you to submit a ticket to us via our ticketing system, linking to this thread or describing the issue you have with PVA/filament breaking in your material station. We probably have a solution for you. 

     

    Hope this helps, have a great day!

    • Like 1
    Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • Ultimaker Transformation Summit
        Visit our virtual showroom and learn more about the Ultimaker ecosystem!
        • 14 replies
      • New here? Register your Ultimaker for free 3D printer onboarding course
        Hi,
         
        Often getting started is the most difficult part of any process. A good start sets you up for success and saves you time and energy that could be spent elsewhere. That is why we have a onboarding course ready for
        Ultimaker S5 Pro Bundle, Ultimaker S5, Ultimaker S3 Ultimaker 2+ Connect.   
        They're ready for you on the Ultimaker Academy platform. All you need to do to gain access is to register your product to gain free access. 
        Ready? Register your product here in just 60 seconds.
          • Like
        • 0 replies
    ×
    ×
    • Create New...