Jump to content
Ultimaker Community of 3D Printing Experts

Recommended Posts

Posted · reset firmware?

Hello all,

I was trying out some new firmware, and I am stuck.

I was able to work with replicatorG and the motors do work, no heating nor extrusion.

Then I tried out some newer firmware, but now I cannot connect anymore.

It says:

Attempting to reset RepRap (pulsing RTS)

Unknown: **********HERE SOME STRANGE SYMBOLS

Any help ?

Thanks,

Peter

  • Link to post
    Share on other sites
    Posted · reset firmware?

    The firmware from:

    http://daid.eu/~daid/marlin_build/

    is recommended.

    But if you want to print from RepG you need to:

    -Set the baudrate to 57600

    -Disable the "software endstops"

    -"Steps per unit" for "E" needs to be 14 with the RepG from Ultimaker.

    Or, you could upgrade to the SkeinPyPy Beta3:

    https://github.com/daid/SkeinPyPy/downloads

    Which helps you installing the right firmware, and allows faster and better slicing.

  • Link to post
    Share on other sites
    Posted · reset firmware?

    The first link I gave you can build a firmware for you, it also contains a batch file that helps you in changing the firmware, this always works, even if RepG cannot connect.

    The settings I said you need to change in the link I gave.

  • Link to post
    Share on other sites
    Posted · reset firmware?

    Ok,I ll try. Thanks.

  • Link to post
    Share on other sites
    Posted · reset firmware?

    Hey Daid,

     

    The firmware from:

    http://daid.eu/~daid/marlin_build/

    is recommended.

    But if you want to print from RepG you need to:

    -Set the baudrate to 57600

     

    I have it set to 115200, it works fine.

     

    The firmware from:

    http://daid.eu/~daid/marlin_build/

    is recommended.

    But if you want to print from RepG you need to:

    -Disable the "software endstops"

    -"Steps per unit" for "E" needs to be 14 with the RepG from Ultimaker.

     

    I have my software stops enabled, is that because I use Netfab?

    I thought the E14 was only for Netfab.

    Hi petermeuris

    Use Daid's link you configure and upload your firmware from there.

    You configure it, download the zip file, run the batch file, enter your com port, ie. COM4 and it does the rest.

    It's great and so is that version of Marlin.

  • Link to post
    Share on other sites
    Posted · reset firmware?

    So I followed your first link, created the software uploaded it, but is tells me:

    avrdude: stk500v2_ReceiveMessage(): timeout

    avrdude: stk500v2_ReceiveMessage(): timeout

    avrdude: stk500v2_ReceiveMessage(): timeout

    avrdude: stk500v2_ReceiveMessage(): timeout

    EDIT: Restarted the ultimaker and ran the uploader again, this uploads the software

    And I can connect again with repG !

    Thanks !!

    Still no heating nor movement in the feeding motor though, the rest works.

    So I have still work to do :-)

  • Link to post
    Share on other sites
    Posted · reset firmware?

    The extruder (feeder) motor won't move unless it's on proper temperature (cold extrusion prevention)

    However, in RepG26 the direct control of the extruder is broken, so you cannot use that to test the extruder. Heating should work however. Be careful, it can be the heater, or the sensor that's not working. If the temperature sensing is not working then you could damage your machine!

  • Link to post
    Share on other sites
    Posted · reset firmware?

    The direct control of the extruder is broken in RepG25 but works in RepG26

  • Link to post
    Share on other sites
    Posted · reset firmware?

    I also checked if the Motherboard was giving any voltage to the white wires, Ii did not. (Voltmeter)

    I was using repG 33 for linux, I have installed v25 and heating works,we are getting closer now.

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • Talking additive | The 3D printing podcast
        Why should we be the only ones asking questions? Join us and ask Jabil all your questions on September 22nd 5pm CET
          • Like
        • 3 replies
      • Ultimaker masterclass: Optimizing your Ultimaker Cura workflow
        Save your seat for either broadcast on September 23.
        What will you learn?
        · Best practices for iterative print preparation and every lesson you should learn from each print
        · The right way to use per-object settings and when they are most useful
        · Easy-to-use resources for anyone who wants to develop their own printer definitions, plugins, or print profiles
        · How to optimize print profile settings and whether to “keep” or “discard” changes
        · When is the right time to export your drawing from CAD? (Based on Ultimaker Cura’s surprising power as 3D control software)
        · And a whole lot more tips and tricks!
         
        How can I join?
        This free masterclass will take place twice:
        1. 11am CEST (5pm SGT, 5am EDT)
        2. 5pm CEST (11am EDT, 8am PDT, 11pm SGT)
          • Like
        • 0 replies
      • Do you use 3D printing at work? Let us know
        It doesn't matter if you are using 1 Ultimaker or 10, there is inspiration in everything. We're looking for ...
        • 1 reply
    ×
    ×
    • Create New...