Jump to content
Ultimaker Community of 3D Printing Experts

Cura 13.11.2 ignores Minimal Layer Time


Recommended Posts

Posted · Cura 13.11.2 ignores Minimal Layer Time

I have a print that ends in a small diameter peak and need to slow down the print or the whole thing is a melty blob. I have tried using 2 and 5 minimal layer time, but I do not see the print slowing at all, it just keeps going at the normal speed.

My expectation would be that it would slow down to the point of only printing 1-layer/Minimal layer time. So if the setting is 2 secs the z-axis should only advance every 2 seconds.

Has anyone else see this, or is there another setting I need to check?

 

  • Link to post
    Share on other sites
    Posted · Cura 13.11.2 ignores Minimal Layer Time

    There is also a setting "min speed". Regardless of how slow your printer wants to move to stay above the desired min layer time, it won't move slower than this min speed. But lowering this"min speed" even more than standard setting I'd not really recommended. This will transfer so much heat from the slow moving head into your print that you will get blobs etc. try printing 2 or more objects at once... Be sure to set your gantry height at 0. (found in printer settings)

  • Link to post
    Share on other sites
    Posted · Cura 13.11.2 ignores Minimal Layer Time

    thanks for the input, I did not notice the min speed.

    So my min speed is set to 10mm/sec, ganrty=0. I am not sure it's slowing to 10mm/sec but I will watch is closely to see if this is the limit I am reaching. (normal print speed 70mm/sec)

    Multiple objects might be the way I need to go.

     

  • Link to post
    Share on other sites
    Posted · Cura 13.11.2 ignores Minimal Layer Time

    What would really help for these sharp tips to print correctly is if the printhead would retract and move away a little, so that no longer the hot-end is touching (and heating) the model, and the print time will actually result in cool-down time. Preferrably the head is moved a little away from the model with the fan on, to let the fan cool the model during the ' minimal layer time' .

    Can I add this feature request somewhere?

     

  • Link to post
    Share on other sites
    Posted · Cura 13.11.2 ignores Minimal Layer Time

    Iluminarti, whats your personal experience with this function...sounds to me like this"cool head lift" could also cause a lot of oozing and pressure loss in the hotend...

  • Link to post
    Share on other sites
    Posted · Cura 13.11.2 ignores Minimal Layer Time

    I haven't used it much... but I did use it for the owl print I did:

    Owl

    There was a bit of oozing during the pauses, which resulted in some junk getting dragged back onto the outside of the ear tips, but it was easy to clean up. I think you'd only want to use it with relatively slow volume/second prints, but I do think it has potential.

     

  • Link to post
    Share on other sites
    Posted · Cura 13.11.2 ignores Minimal Layer Time

    Thanks...

  • Link to post
    Share on other sites
    Posted · Cura 13.11.2 ignores Minimal Layer Time

    Coen, it's already there. Expert -> Open Expert Settings -> Cool Head Lift

     

    Ha, never noticed that one! Great, I will give it a try.

     

  • Link to post
    Share on other sites
    Posted · Cura 13.11.2 ignores Minimal Layer Time

    I don't like cool head lift - it tends to make vertical strings. I wish there was a sideways head pause. The best looking result solution is to print a tower (or print two items) next to your print.

    I set my minimum speed to 0. Never had a problem with it. I think it was more for the old ultimaker V1 print head which was updated over a year ago.

     

  • Link to post
    Share on other sites
    Posted · Cura 13.11.2 ignores Minimal Layer Time

    thanks all. for sure this is not a bug.

    it is me trying to understand the settings and getting them right for this print. I will start a new thread describing my diffculty with printing this model under the "Questions & Answers (Help Each Other)" forum. thanks again for the great input, and pointing me in the right direction.

     

  • Link to post
    Share on other sites
    Posted · Cura 13.11.2 ignores Minimal Layer Time

    Post pictures. That's the best way to get useful advice.

     

  • Link to post
    Share on other sites
    Posted · Cura 13.11.2 ignores Minimal Layer Time

    Personally I use all, or a combination of (all depends on the size and geometry)

    • print two off the pieces concurrently (same as using a tower but can be more productive)
    • set minimum layer time to 10 secs (I know George likes to go lower but it suits me).
    • minimum speed to 10mm/s
    • also I have been using z-lift in recent months which has been effective. Yes you can suffer from oozing but with a little practice you can wipe that away just before the head moves back to print the next layer
    • fans 100%

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • Talking additive | The 3D printing podcast
        Why should we be the only ones asking questions? Join us and ask Jabil all your questions on September 22nd 5pm CET
        • 3 replies
      • Ultimaker masterclass: Optimizing your Ultimaker Cura workflow
        Save your seat for either broadcast on September 23.
        What will you learn?
        · Best practices for iterative print preparation and every lesson you should learn from each print
        · The right way to use per-object settings and when they are most useful
        · Easy-to-use resources for anyone who wants to develop their own printer definitions, plugins, or print profiles
        · How to optimize print profile settings and whether to “keep” or “discard” changes
        · When is the right time to export your drawing from CAD? (Based on Ultimaker Cura’s surprising power as 3D control software)
        · And a whole lot more tips and tricks!
         
        How can I join?
        This free masterclass will take place twice:
        1. 11am CEST (5pm SGT, 5am EDT)
        2. 5pm CEST (11am EDT, 8am PDT, 11pm SGT)
        • 0 replies
      • Do you use 3D printing at work? Let us know
        It doesn't matter if you are using 1 Ultimaker or 10, there is inspiration in everything. We're looking for ...
          • Like
        • 1 reply
    ×
    ×
    • Create New...