Jump to content
Ultimaker Community of 3D Printing Experts

Cura 4.8 bug?


Recommended Posts

Posted · Cura 4.8 bug?

I just sliced a new design.  It's fairly simple.  A 30x230 mm cylinder with M18 threads cut into each end.  The cylinder showed the internal threads in cura, but when I printed it, it printed solid with no 18mm hole or threads.

 

The stl file is fine as far as I can tell.  A similar design printed fine at 240mm with identical settings.  I created a shorter one to fit my printer better.

 

Just logging it in case it pops up elsewhere.  The one with the problem was printed vertically.  I'm going to try it horizontally and see if the threads are there.

  • Link to post
    Share on other sites
    Posted · Cura 4.8 bug?

    Ok, I did a couple of tests.  First, the same stl file printed the internal threads when the object was horizontal.  Too bad they are threads and a cylinder that need to be printed vertically.

     

    Next, I reloaded the stl and looked at the preview, and in fact the internal cylinder and threads appeared as infill, which is how it printed (no top or bottom layer, just exposed infill).  I guess I missed that the first time.

     

    I then loaded 4.7.1 back and it renders fine.  So it is definitely a bug in 4.8.

     

    Let me know if you want the stl.  Like I said its pretty basic and it would probably be faster to design one than wait for me to send it.   I designed it in fusion 360 if that means anything.

     

    I'm sticking with 4.7.1 for now.

  • Link to post
    Share on other sites
    Posted · Cura 4.8 bug?

    Ok, I did a couple of tests.  First, the same stl file printed the internal threads when the object was horizontal.  Too bad they are threads and a cylinder that need to be printed vertically.

     

    Next, I reloaded the stl and looked at the preview, and in fact the internal cylinder and threads appeared as infill, which is how it printed (no top or bottom layer, just exposed infill).  I guess I missed that the first time.

     

    I then loaded 4.7.1 back and it renders fine.  So it is definitely a bug in 4.8.

     

    Let me know if you want the stl.  Like I said its pretty basic and it would probably be faster to design one than wait for me to send it.   I designed it in fusion 360 if that means anything.

     

    I'm sticking with 4.7.1 for now.

     

    Ok, I just noticed I could upload.  here is the stl

    handle-sect-230.stl

  • Link to post
    Share on other sites
    Posted · Cura 4.8 bug?

    I sliced it as well with 4.8.  Has open threads top and bottom, same as shown by Greg V.

  • Link to post
    Share on other sites
    Posted · Cura 4.8 bug?

    Hmm, ok, there was something unusual in the slicer settings.  10 wall layers and 6 top/bottom, and fwiw, 75% gyroid fill.  This may be overkillm, but the part prints like a rock.  It will be used as a harpoon, so needs to have weight and good impact resistance.  

     

    Glad to hear it worked for you.   I'll try it again when I get a chance, maybe play with the layers and fill.

     

    Thanks for looking into it!

  • Link to post
    Share on other sites
    Posted · Cura 4.8 bug?

    Oh, and here is the gcode file that shows no threads or internal hole.

    handle-sect-230.gcode

  • Link to post
    Share on other sites
    Posted · Cura 4.8 bug?

    Reviewing your Gcode file the model sliced perfectly.  You asked Cura to "Remove all holes" and it did.  No problem.

  • Link to post
    Share on other sites
    Posted · Cura 4.8 bug?

    This is a follow-up to my last post when I was having difficulty getting Cura 4.8.0 to connect over USB to my ANET A8 printer.

     

    Great news.  I got Cura working, thanks to an excellent YouTube video. It was short and directly to the point, with complete instructions for fixing it. The video is "How to fix Cura or Slicer Not CONNECTING to 3D Printer Creality Ender 3?" by Joseph-Israel.

    Turns out that Cura doesn't allow long enough for the Marlin 1.1.9.1 FW to initialize
    on the ANET A8 8-bit board. The following modification will tune Cura to wait longer
    to connect after it reboots the printer.

    Inside file C:\Program Files\Ultimaker Cura 4.8.0\plugins\USBPrinting\AutoDetectBaudJob.py

    Change:
    wait_bootloader_times = [1.5, 5, 15]
    To:
    wait_bootloader_times = [5, 15, 30]
     

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • Startups, apply for the Forward AM Innovation Award!
        Are you a startup using 3D printing? Perhaps you should continue reading... 
         
        Together with BASF we are launching the Forward AM Innovation Award - the very first global contest for startups developing new applications with 3D printing!
         
        Why apply?
        The winning startup will receive €100,000 in goods and services*, along with coaching and marketing exposure from top-notch leaders in the industry.
         

         
        Who can apply?
        Your startup creates products using Additive Manufacturing, is less than 5 years old, and has less than 50 employees. We are looking for 3D printing applications with a strong focus on innovation, sustainability and scalability.
         
        Dental aligners, shoes, tools, automotive parts, music instruments, industrial tooling and molding, medical implants, sports equipment, toys, architecture, fashion, construction... all are welcome to join!
         
        Do you have an innovative, sustainable and scalable idea that leverages the unique possibilities of 3D printing? Then it is time to apply!
        More information can be found here.
         
        Applications close on March 28th, 2021
        * What does "in goods and services" mean?
        The winner will be able to pick any item from the overall product and service portfolio of the sponsors, e.g. printers, materials, consulting, software... Choose whatever you need to accelerate your startup.
         
          • Like
        • 0 replies
      • New here? Register your Ultimaker for free 3D printer onboarding course
        Hi,
         
        Often getting started is the most difficult part of any process. A good start sets you up for success and saves you time and energy that could be spent elsewhere. That is why we have a onboarding course ready for
        Ultimaker S5 Pro Bundle, Ultimaker S5, Ultimaker S3 Ultimaker 2+ Connect.   
        They're ready for you on the Ultimaker Academy platform. All you need to do to gain access is to register your product to gain free access. 
        Ready? Register your product here in just 60 seconds.
          • Like
        • 0 replies
    ×
    ×
    • Create New...