Jump to content
Ultimaker Community of 3D Printing Experts

UM2+ Regulator on Main Board Burn't.


Recommended Posts

Posted · UM2+ Regulator on Main Board Burn't.

Hello, 

So i have a Ultimaker 2+ since 2015 and some weeks ago i started a normal print with 3/4h and after 1h i came to the machine and the machine was tuned off. 

I tried to turn on again, no luck, no signal, no lights, nothing.... Started to dig, and the power adapter was fine, 24v on output everything fine.. 
Started to take off the main board and searching for burned components, and after a while i noticed a little "dot" on the regulator.. 

I thought "the regulator was gone", so, i ordered a bunch of them from farnell, same reference, and replace them, but after turn on the button the regulator is fried instantly. 

Anyone has passed for this? Any thought what can be? Some capacitor? 

I will leave here a video with test with a controlled power and we can see that the regulator start's to heat up wildly and burn's after a while. 
 

https://youtu.be/Iy4ykeSaOLo


(other question if i can't solve this, the china boards from ebay/aliexpress are reliable?, anyone with one? problems encountered? )
 
Thanks,
André.

PHOTO-2020-12-09-19-45-59.jpg

  • Link to post
    Share on other sites
    Posted · UM2+ Regulator on Main Board Burn't.

    Hi @AndreCarvalho,

     

    When we change this kind of switch regulator, we'll also change the fly back diode (D16) as well.

    When you look at your thermal picture, there is two hot spot.. And the other is this diode.

    Also check that the 5VDC out line have no direct ground (other circuits might cause the power supply to fry).

     

    Normally it's only this two active components that's fails like this.

     

    Ok., good luck.

     

    Thanks

    Torgeir

  • Link to post
    Share on other sites
    • 1 month later...
    Posted · UM2+ Regulator on Main Board Burn't.

    Hello,

    After some time running (75h +-),  after a while the UM2+ restarts without reason.

    Today morning i tried to heat the extruder manually in the "Advanced" menu and she restarted.. 
    Other test made is start a print and after half an hour it restarts, but while is printing the leds seems to slightly blink.

    Anyone with this problem?


     

  • Link to post
    Share on other sites
    Posted (edited) · UM2+ Regulator on Main Board Burn't.

    Hi,

     

    You might have an issue with the power fluctuating! It might be due to your power connector feeding system, or due to some component (located at the main PCB or external component connected to this PCB) drawing to much current intermittent.  An intermittent power drop will cause the processor to restart..

     

    Easiest -is to try another power supply..  Since this occur also cause loss of 5 VDC, -the main power for the processor.

    But might also be sign of a failing component taking down the 5 V DC power converter for the second time..  There might be a sign of an overheat on another component, did you check?

     

     

     

    Thanks

    Torgeir

     

     

     

    Edited by Torgeir
    Error and more info.
  • Link to post
    Share on other sites
    Posted · UM2+ Regulator on Main Board Burn't.

    Hello Torgeir,

    Yes, everything seems fine, and this problem occurred to me a year ago more or less, but the printer was fine for 8 months or more, then after that it burned the D16 and the stepdown, and now it's doing the same thing as a year ago.

    I'm printing now for 2h with the heatbed turned off and it seems to be fine, and for what i've checked here in the forum the Power brick may be the cause right? 

    Need to burn more 80+€.. damn printers.... 😞

    Br,
    André.



     

  • Link to post
    Share on other sites
    Posted · UM2+ Regulator on Main Board Burn't.

    Hi André,

     

    Good test, -printing without using the heat bed -in order to sort out of a such a problem..

    Sure, the power supply always takes the heavy load, and it's the problem in (80-95)% of ~all kind of electronics failures, -cause they are very often under dimensioned!

     

    As usual, good luck.

    Best regard

    Torgeir

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • Startups, apply for the Forward AM Innovation Award!
        Are you a startup using 3D printing? Perhaps you should continue reading... 
         
        Together with BASF we are launching the Forward AM Innovation Award - the very first global contest for startups developing new applications with 3D printing!
         
        Why apply?
        The winning startup will receive €100,000 in goods and services*, along with coaching and marketing exposure from top-notch leaders in the industry.
         

         
        Who can apply?
        Your startup creates products using Additive Manufacturing, is less than 5 years old, and has less than 50 employees. We are looking for 3D printing applications with a strong focus on innovation, sustainability and scalability.
         
        Dental aligners, shoes, tools, automotive parts, music instruments, industrial tooling and molding, medical implants, sports equipment, toys, architecture, fashion, construction... all are welcome to join!
         
        Do you have an innovative, sustainable and scalable idea that leverages the unique possibilities of 3D printing? Then it is time to apply!
        More information can be found here.
         
        Applications close on March 28th, 2021
        * What does "in goods and services" mean?
        The winner will be able to pick any item from the overall product and service portfolio of the sponsors, e.g. printers, materials, consulting, software... Choose whatever you need to accelerate your startup.
         
          • Like
        • 0 replies
      • New here? Register your Ultimaker for free 3D printer onboarding course
        Hi,
         
        Often getting started is the most difficult part of any process. A good start sets you up for success and saves you time and energy that could be spent elsewhere. That is why we have a onboarding course ready for
        Ultimaker S5 Pro Bundle, Ultimaker S5, Ultimaker S3 Ultimaker 2+ Connect.   
        They're ready for you on the Ultimaker Academy platform. All you need to do to gain access is to register your product to gain free access. 
        Ready? Register your product here in just 60 seconds.
          • Like
        • 0 replies
    ×
    ×
    • Create New...