Jump to content

Network issues

mjhangge

By mjhangge
in UltiMaker 3D printers

 Share

Recommended Posts

mjhangge

mjhangge 0

Posted
Posted · Network issues

My S5 will not connect to my wifi network. I have upgraded to 6.1.1, I have run through the wifi setup dozens of times, I've reset everything, I've tried to download the wifi via USB twice. I've tried to connect via ethernet. Nothing seems to work. It won't even allow me to turn on the wifi or ethernet. Any suggestions for me?

    • Link to post
    Share on other sites
    SpencerPlastics

    SpencerPlastics 0

    Posted
    Posted · Network issues
    On 2/9/2021 at 8:35 PM, mjhangge said:

    My S5 will not connect to my wifi network. I have upgraded to 6.1.1, I have run through the wifi setup dozens of times, I've reset everything, I've tried to download the wifi via USB twice. I've tried to connect via ethernet. Nothing seems to work. It won't even allow me to turn on the wifi or ethernet. Any suggestions for me?

     

    We have had the same issue a few times.  Power cycle and i have been able to get connected back to WIFI again.  The ethernet has never allowed us to enable it.  I have tried creating a config file and importing it but this did nothing.

    • Link to post
    Share on other sites
    gr5

    gr5 2,167

    Posted
    Posted · Network issues

    Better than power cycle is to do the "cura connect reset" in the maintenance menu.  I think they changed the name in newer firmware - too lazy to turn on S5 and wait, sorry.  Don't do factory reset - the other one.

    • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
     Share
    Followers 1
    Go to topic listing

    • Our picks

      • UltiMaker Cura 5.7 stable released

        UltiMaker Cura 5.7 stable released

        ArunC posted a topic in UltiMaker Cura,

        Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
         
          • Like
        • 18 replies
        MariMakes

        Picked By

        MariMakes,

      • Release Notes: S-Line Firmware 8.3.0 (Latest)

        Dustin posted a topic in Firmware,

        S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
        (Sorry, was out of office when this released)

        This update is for...
        All UltiMaker S series  
        New features
         
        Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
          • Like
        • 0 replies
        MariMakes

        Picked By

        MariMakes,
      View All
    ×
    ×
    • Create New...