Jump to content

Was ist hier los?

radio-heini68

By radio-heini68
in Deutsch

 Share

Recommended Posts

radio-heini68

radio-heini68 0

Posted
Posted · Was ist hier los?

Hallo,

ich habe seit einigen Tage Probleme beim Drucken von Überhängen, siehe Bild.

An meinen Einstellungen in CURA habe ich nichts geändert.

Was ist hier los? Habe ich einen Defekt in der Hardware? Es werden aber keinerlei Fehlermeldungen angezeigt.

 

Wer kann helfen?

 

Gruß Markus

20210627_121700.jpg

    • Link to post
    Share on other sites
    curatori

    curatori 7

    Posted
    Posted (edited) · Was ist hier los?

    Das sieht mir nach zu hoher Temperatur aus.
    Bei diesen kleinen Flächen hat das Material nicht genug Zeit zum Abkühlen, dann wölbt es sich hoch.
    Entweder zwei Teile drucken oder stärker kühlen.

    Und erst innen, dann außen drucken.

     

    Gruß Michael

     

    Edited by curatori
    • Link to post
    Share on other sites
    UlrichC-DE

    UlrichC-DE 109

    Posted
    Posted · Was ist hier los?

    Hallo

     

    würde prüfen, ob die Bauteillüfter. Also die beiden an den Seiten des Druckkopfs noch arbeiten.

    Falls der Drucker der Witterung des Sommers ausgesetzt ist, (auf dem Dachboden steht oä.) kann das genauso ausschauen.

     

    Viele Grüße

    • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
     Share
    Followers 3
    Go to topic listing

    • Our picks

      • UltiMaker Cura 5.7 stable released

        UltiMaker Cura 5.7 stable released

        ArunC posted a topic in UltiMaker Cura,

        Cura 5.7 is here and it brings a handy new workflow improvement when using Thingiverse and Cura together, as well as additional capabilities for Method series printers, and a powerful way of sharing print settings using new printer-agnostic project files! Read on to find out about all of these improvements and more. 
         
          • Like
        • 18 replies
        MariMakes

        Picked By

        MariMakes,

      • Release Notes: S-Line Firmware 8.3.0 (Latest)

        Dustin posted a topic in Firmware,

        S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
        (Sorry, was out of office when this released)

        This update is for...
        All UltiMaker S series  
        New features
         
        Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
        • 0 replies
        MariMakes

        Picked By

        MariMakes,
      View All
    ×
    ×
    • Create New...