Jump to content
Sign in to follow this  
mark-hale

Switching material mid print

Recommended Posts

Posted · Switching material mid print

Well I figured it would happen at some point, just glad I was around when it did.

Over the weekend I was running a rather long print 15 hours with 100% fill so a fair bit of material.

My estimate was slightly under so in the last 30 minutes I realised I would run out of PLA.

I managed to feed in a new section just as the other one was running out.

The reason I am posting this was more from a Lessons learnt on my point but hopefully it will help others.

trying to get the other section of PLA in without interrupting the extrusion of the original was not as easy as I thought, I realised after that I should have slowed down the print to allow me more time as there was a point where the material stopped flowing albeit very brief. Due to the new material not catching in time.

I should have also been a little more careful with cutting the end of the new material to ensure that it met the old material flush and therefore made a better contact.

So whilst I do have a part that has a very slight gap however the print did continue and apart from a small line gap and then the obvious change in material type all worked well.

On the whole I am quite happy with the results, the print is nothing special, just a repair to a small sack trolley.

The experience has got me thinking - I am using an UM2 and so at present whilst I do not have dual extrusion, I might be able to use this method to at least get some alternate coloured prints. I might try this at some point with the various short ends I now have in the workshop. Saves it going to waste. :)

 

Share this post


Link to post
Share on other sites
Posted · Switching material mid print

There are a few methods for connecting material available (e.g.on Thingiverse) but as a KISS solution I used a torch/lighter for melt/conduct and a knife for making the connection point as 3mm and round as possible.

Worked for me, but I only I connected some short samples with this method...

 

Share this post


Link to post
Share on other sites
Posted · Switching material mid print

Somewhat relevant to the issue at hand... I've no idea if this stuff is any good, but these people keep emailing me trying to get me to be a reseller...

http://www.stickfilament.com

Apparently it's half-meter lengths of filament that snap together to make whatever length you need for a print. Supposedly because the filament is moulded as discrete pieces rather than extruded continuously, it's easier to manufacture material with different properties, and of course combining multiple materials/colors in one print becomes easier (albeit only on predefined boundaries).

 

Share this post


Link to post
Share on other sites
Posted · Switching material mid print

certainly looks interesting, I could be tempted to give it a go. Although I guess it is only for small runs or where you are going to be close at hand as think that would be an issue trying to put on a spool

have just put in a pre order for a pack so will let you know. They are up to 76 orders, need 100 so could be while?

 

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Sign in to follow this  

  • Our picks

    • Ultimaker Cura | a new interface
      We're not only trying to always make Ultimaker Cura better with the usual new features and improvements we build, but we're also trying to make it more pleasant to operate. The interface was the focus for the upcoming release, from which we would already like to present you the first glance. 
        • Like
      • 181 replies
    • "Back To The Future" using Generative Design & Investment Casting
      Designing for light-weight parts is becoming more important, and I’m a firm believer in the need to produce lighter weight, less over-engineered parts for the future. This is for sustainability reasons because we need to be using less raw materials and, in things like transportation, it impacts the energy usage of the product during it’s service life.
        • Like
      • 12 replies
×
×
  • Create New...

Important Information

Welcome to the Ultimaker Community of 3D printing experts. Visit the following links to read more about our Terms of Use or our Privacy Policy. Thank you!