Jump to content
Ultimaker Community of 3D Printing Experts

Profil Geeetech A30T/ Probleme mehrfarbdruck


djseppo
 Share

Recommended Posts

Posted · Profil Geeetech A30T/ Probleme mehrfarbdruck

Hallo, gibt es mitlerweile ein Profil für den A30T?

Mit dem angepassten vom A20T kann ich zwar bestens einfarbig drucken, aber beim mehrfarbig geht fast alles in die hose.

Entweder es verschiebt mitten im Druck die schicht, weil er zum farbe wechseln auf dem druck stehen bleibt und dann etwas filament rausläuft, er somit einen haufen bildet und dann bei den folgenden Layern drüber hoppelt, oder er füllt gar nict erst und zieht das filament nur von einem der drei Extruder.

 

IMG_2022.jpg

IMG_2023.jpg

IMG_2024.jpg

IMG_2025.jpg

  • Link to post
    Share on other sites

    Posted (edited) · Profil Geeetech A30T/ Probleme mehrfarbdruck

    Because the 2-in-1-out and the 3-in-1-out hot ends are relatively new, you need to experiment with the settings.  I would think that Reddit or maybe a users group on Facebook could be helpful in setting Cura up to work with your printer.  Does Geetech have a forum?

     

    Do you have the "Printer Settings" plugin loaded (from the MarketPlace)?  It has the "extruders share heater" and "extruders share nozzle" settings within it.

    There may be settings in the Dual Extruder section that need to be adjusted.

    Each extruder can have it's own start and end gcode.  Those allow for further custimization.

     

    I have configured virtual printers with 3 extruders and generated gcodes but I don't actually have one.  I know that if you make a change to an extruder, it is only for that extruder.  Each has to be altered separately in Cura.

    Reality often gets in the way of my virtual printing experience so I'll go no further with this.

     

    Good Luck.

    PS:  Those are possibly the ugliest geckos I've ever seen.  I think that just for practicing I'd load 3 calibration cubes and set each one to a different extruder.  That should cut back on your filament usage while you get it dialed in.  Getting to and from the prime tower without making a mess will be a key.

    Edited by GregValiant
  • Link to post
    Share on other sites

    Posted · Profil Geeetech A30T/ Probleme mehrfarbdruck

    Hallo

     

    ich hatte das Problem auch hab aber als ersten die extruderantriebe gewechselt gegen Bmg clone .. dann hab ich das ganze umgebaut auf purge bucket im Cura und dann lief das auch ..

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
     Share

    • Our picks

      • New here? Get ahead with a free onboarding course
        Hi,
         
        Often getting started is the most difficult part of any process. A good start sets you up for success and saves you time and energy that could be spent elsewhere. That is why we have a onboarding course ready for
        Ultimaker S5 Pro Bundle, Ultimaker S5, Ultimaker S3 Ultimaker 2+ Connect.   
        They're ready for you on the Ultimaker Academy platform. All you need to do to gain access is to register your product to gain free access. 
        Ready? Register your product here in just 60 seconds.
          • Like
        • 11 replies
    ×
    ×
    • Create New...