Jump to content

[CURA 4.10] forme ouverte remplie systématiquement, litophane problème [RESOLU]


Catlord

Recommended Posts

Posted (edited) · [CURA 4.10] forme ouverte remplie systématiquement, litophane problème [RESOLU]

Hello,

j'ai installé cura 4.1 et j'ai un gros soucis avec.

je fait des litophanes sphérique et des que je slice, CURA me rempli complètement l'intérieur de la sphere ce qu'il n'a jamais fait avant.

Dans le doute j'ai chargé un ancien litophane ( le nouveau posait peut être problème) : même résultat.

 

J'ai donc alors crée une figure ouverte : un cube sans fond avd 2mm de paroie: MEME RESUL¨TAT !

J'ai essayé infil 100%, nombre de mur 99 = cura rempli tout. si je met nombre de murs 10, il me mets 10 murs. ca parait logique mais en fait non: cura semble considèrer qu'une forme ouverte (et exempte de défauts: c'est bien water tight, pas de soucis) doit être remplie.

C'est une nouvelle fonctionnalité ? 

 

Note: j'ai slicer le même STL dans prusaslicer et là, pas de problèmes.

Je préfère LARGEMENT CURA pour les lito, il gère bien mieux l'impression des trucs fin. Toutes mes sphère sous prusaslicer sortent degueulasses ^^

 

  Merci pour votre aide qui se révélera précieuse 🙂

Capture1.PNG

Capture2.PNG

Edited by Catlord
  • Link to post
    Share on other sites

    Posted · [CURA 4.10] forme ouverte remplie systématiquement, litophane problème [RESOLU]

    Si CURA rempli ton objet, c'est que ton objet, à défaut d'être étanche, a une face dont la normale est inversée et/ou invisible, point.

  • Link to post
    Share on other sites

    Posted · [CURA 4.10] forme ouverte remplie systématiquement, litophane problème [RESOLU]

    Cet article avait été rédigé en prenant Sketchup comme exemple, mais c'est valable pour tous les logiciels qui essayent de tripoter du triangle...
     

  • Link to post
    Share on other sites

    Posted · [CURA 4.10] forme ouverte remplie systématiquement, litophane problème [RESOLU]

    ALors justement pour partir sur une base qui ne laisse aucun doute, j'ai fait ce cube avec une peau de 2mm. et une face vide . Il n'y a pas de doutes, il n'y a pas de défaut.

    Prusaslicer le slice proprement, CURA 4.1 me sors un truc imbitable.

    Y z'auraient pas foutu une option hollow à la con quelque part ?

     

  • Link to post
    Share on other sites

    Posted (edited) · [CURA 4.10] forme ouverte remplie systématiquement, litophane problème [RESOLU]

    Voici le cube en question

     

    model1.stl

     

    Je viens de tomber sur ce post qui présente le même genre de soucis.

     

     

     

    Edited by Catlord
  • Link to post
    Share on other sites

    Posted · [CURA 4.10] forme ouverte remplie systématiquement, litophane problème [RESOLU]

    Quand j'ouvre ton STL dans CURA, effectivement, il est clean et bien découpé vide et tout et tout....

    Recharge un profile par défaut pour supprimer un truc coché qqpart...

    • Like 1
    Link to post
    Share on other sites

    Posted · [CURA 4.10] forme ouverte remplie systématiquement, litophane problème [RESOLU]

    Problème résolu avec la méthode freebox

    désinstalle, réinstalle.

    A priori c'était un problème de profile d'imprimante qui foirait tout. 

  • Link to post
    Share on other sites

    Posted · [CURA 4.10] forme ouverte remplie systématiquement, litophane problème [RESOLU]

    @darkdvd : merci de ta réactivité 😉

  • Link to post
    Share on other sites

    Posted · [CURA 4.10] forme ouverte remplie systématiquement, litophane problème [RESOLU]

    De rien.

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • Introducing Universal Cura Projects in the UltiMaker Cura 5.7 beta
        Strap in for the first Cura release of 2024! This 5.7 beta release brings new material profiles as well as cloud printing for Method series printers, and introduces a powerful new way of sharing print settings using printer-agnostic project files! Also, if you want to download the cute dinosaur card holder featured below, it was specially designed for this release and can be found on Thingiverse! 
          • Like
        • 10 replies
      • S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
        (Sorry, was out of office when this released)

        This update is for...
        All UltiMaker S series  
        New features
         
        Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
          • Like
        • 0 replies
    ×
    ×
    • Create New...