Jump to content
Ultimaker Community of 3D Printing Experts

Ultimaker ABS


SandervG
 Share

Recommended Posts

Posted · Ultimaker ABS

Ultimaker ABS is formulated to minimize warping and ensure consistent interlayer adhesion, which can be an issue with ABS. ABS has been a popular material for many years already. But more and more alternatives appear on the market. When should you use ABS or when should pick something else? Ask us below in the comments! Community experts, Ultimaker experts and material experts are available to help. 


Have you printed with Ultimaker ABS before? Let us know what you think! It could be useful for customers considering to use it. 
 

  • Link to post
    Share on other sites

    Posted · Ultimaker ABS

    I often use Ultimaker ABS because it has the best adhesion compared to other ABS filaments.
    Ultimaker ABS is also harder than other ABS filaments, such as those from BASF.

     

    What I generally like about ABS is that it can be glued with acetone. ABS can be painted without significant preparation and plastic primer. I have printed every available filament that Ultimaker offers. Including PP and PET-G.
    So far, I don't know of any other plastic where post-processing is so easy.

     

    The good layer adhesion of Ultimaker ABS is not only reflected in the improved stability, but unfortunately also in its weight. Prints made with Ultimaker ABS are therefore just as heavy as PLA. (Not scientifically measured but only an empirical value)

     

    Last but not least, Ultimaker ABS is one of the cheaper filamants in the range, next to PLA.
    I print 50% of my prototypes, and it almost doesn't matter what they are printed from. PLA suffers in the post-processing and in the durability in relation to heat exposure. Therefore, in most cases for me and my technical parts actually only ABS remains.

     

    The somewhat different ABS resume:
    - permanent bonding / yes
    - surface smoothing / yes
    - Painting / yes
    - Drilling / thread cutting / yes
    - Inexpensive / yes
    - Easy to print / yes

  • Link to post
    Share on other sites

    Posted · Ultimaker ABS

    For the athesion or to protect the glass plate, I usually use (very old-fashioned) hairspray.
    Where I also, pretty much everything except PLA parts in monster format, print without Brim.

     

    Depending on the ABS parts I print...
    - for very small parts (0.25 stuff)
    - for a lot of parts
    .. Magigoo is used as an alternative.

     

    In addition, I have gained the experience that with large-area parts that are often cemented into the glass plate with 0.4 nozzles, 0.8 nozzles have a more homogeneous athesion.
    The parts can be removed from the printer after cooling without filler. The glass plates remain intact. 

    • Thanks 1
    Link to post
    Share on other sites

    Posted · Ultimaker ABS

    Thank you for your response @UlrichC-DE! For some context, I have created these topics recently because we're adding links to the Ultimaker Marketplace materials (Ultimaker filament), to guide people to our discussion platform if they have any questions about said material. Reading about other peoples experience is also incredibly helpful I reckon. So thanks for taking the time to write down your experience with Ultimaker ABS!

     

    Since you mention you used all Ultimaker filaments, I think everyone could appreciate it if you could be bothered to add your experience of some other Ultimaker filaments too, when you would have a moment. At your convenience of course 🙂

     

    Your experience with Ultimaker ABS, has that always been in combination with the UMS5 Pro Bundle incl Air Manager, or have you also printed it on other machines? 

     

  • Link to post
    Share on other sites

    Posted · Ultimaker ABS

    I use the Ultimaker ABS on UM2+ as well as on S5 pro bundle.

     

    Two UM2+ are each equipped with the same Ultimaker ABS. Currently in gray (RAL7016).
    Because two printers are twice as fast as just one.
    The Filamant lends itself to the above reasons. I have the UM2+ in another room, out of my observation.
    On it run mostly technical end user parts. That's why I chose the most reliable combination imaginable for it, based on experience.

     

    I think if you can get over using Ultimaker's slightly more expensive NFC Tag ABS rolls on the UM2+, you get Fire and Forget - at the next level.

     

    @SandervG

     I'm thinking about what I can come up with to write about the other filaments.

    • Thanks 1
    Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
     Share

    • Our picks

      • The Ultimaker Showcase — October 14. What's new?
        Your dear friends at Ultimaker have some exciting news and insights for you!
         
        • 0 replies
      • New here? Get ahead with a free onboarding course
        Hi,
         
        Often getting started is the most difficult part of any process. A good start sets you up for success and saves you time and energy that could be spent elsewhere. That is why we have a onboarding course ready for
        Ultimaker S5 Pro Bundle, Ultimaker S5, Ultimaker S3 Ultimaker 2+ Connect.   
        They're ready for you on the Ultimaker Academy platform. All you need to do to gain access is to register your product to gain free access. 
        Ready? Register your product here in just 60 seconds.
          • Like
        • 8 replies
    ×
    ×
    • Create New...