Jump to content

problème avec la machine creality CR-10 Max -


valentinehd

Recommended Posts

Posted · problème avec la machine creality CR-10 Max -

Bonjour,

 

Le PLA de notre imprimante sortait très bien jusqu'à ce qu'on fasse un essai avec du filament TPE flexible.

Nous avons remis le PLA normal et maintenant cela fait des micro fils qui n'adhèrent pas et les boulettes.

 

Que faire ???

 

Merci 

 

Valentine

  • Link to post
    Share on other sites

    Posted · problème avec la machine creality CR-10 Max -

    (。▼皿▼)   déjà la fin du Zen.   

    Sinon je dirais voir si le tube du bowden n'est pas bouch", démonter et en profiter pour le changer par un tube PTFE Capricorn , Moins de 15 € sur Amazon et on peut en faire deux dans la longueur livrée.

  • Link to post
    Share on other sites

    Posted · problème avec la machine creality CR-10 Max -
    13 hours ago, valentinehd said:

    Le PLA ... sortait très bien ... essai ... TPE flexible. 

    Nous avons remis le PLA normal et maintenant cela fait des micro fils qui n'adhèrent pas et les boulettes.


    = buse contenant des dépôts du filament précèdent.

  • Link to post
    Share on other sites

    Posted · problème avec la machine creality CR-10 Max -
    1 hour ago, darkdvd said:


    Zen, c'est mon deuxième prénom
     

    dommage que tu n'utilises que le premier! 

     

    pour un nettoyage de buse efficace, ma solution est radicale. démontage de la buse,  un coup de chalumeau et remontage.

     

     

     

    • Like 1
    Link to post
    Share on other sites

    Posted · problème avec la machine creality CR-10 Max -

    Solution n°2 : utiliser une buse différente en fonction du matériau ... je sais, si tu as des Prints Cores, c'est plus cher 😁

  • Link to post
    Share on other sites

    Posted (edited) · problème avec la machine creality CR-10 Max -

    Bonjour !

    Merci beaucoup de vos réponses. 

     

    Comme vous me l'avez conseillé, j'ai démonté la buse et nettoyé entièrement. Elle était effectivement pas très propre ... mais désormais elle brille de propreté !

    J'ai effectué un nouveau test et le débit du PLA est fluide.

    Un problème subsiste cependant ... la première couche de PLA a du mal à s'attacher sur le plateau, elle n'adhère pas bien. Je ne sais pas si c'est dû à un problème de température ou autre. J'ai testé une laque mais rien ne change.

    Mes réglages sont les suivants:

    Température plateau 60°C

    Température nozzle 195°C

    Température PLA 210°C (comme indiqué sur la bobine)

    Vitesse d'impression 50

     

    De plus quand la machine fait le niveau avant de commencer l'impression, des filaments coulent de la buse. Je vous ai fait une photo. Je n'ai pas l'impression que ça le faisait avant ...

     

    Merci beaucoup 

    IMG_2236.JPG

    Edited by valentinehd
  • Link to post
    Share on other sites

    Posted · problème avec la machine creality CR-10 Max -

    Là, c'est un problème avec l'imprimante donc hop hop hop, on va sur le bon forum !

    ps : pas étonnant que ça n'adhère pas en imprimant à l'envers.

  • Link to post
    Share on other sites

    Posted (edited) · problème avec la machine creality CR-10 Max -

    It should not drool when attached to the ceiling.  I'm not sure if gravity is a Zen thing.  It is definitely Newtonian.

     

    It's possible your Z offset for the ABL is off by a little and the Initial layer is a bit too tall.  Cura has a setting for "Initial Layer Flow" in the Material section.  Try setting it to 105% (but this is a band-aid fix). 

     

    Your nozzle is heating all the way to "Initial Layer Print Temperature" and so it is oozing.  Within your StartUp Gcode make the alterations that are in bold text:

     

    M201 X500.00 Y500.00 Z100.00 E5000.00 ;Setup machine max acceleration

    M203 X500.00 Y500.00 Z10.00 E50.00 ;Setup machine max feedrate

    M204 P500.00 R1000.00 T500.00 ;Setup Print/Retract/Travel acceleration

    M205 X8.00 Y8.00 Z0.40 E5.00 ;Setup Jerk

    M220 S100 ;Reset Feedrate

    M221 S100 ;Reset Flowrate

    M140 S{material_bed_temperature_layer_0} ;start to heat the bed

    M109 S150 ;warm up the hot end and wait for it

    M190 S{material_bed_temperature_layer_0} ;wait for the bed

    G28 ;Home

    G29 ;Auto bed Level

    G0 F1800 Z10 ;move the nozzle up so it has room to ooze

    M109 S{material_print_temperature_layer_0} ;wait for the hot end to reach Initial Layer Print Temp

    G92 E0 ;Reset Extruder

    ;G1 Z2.0 F3000 ;Move Z Axis up ;add the semi-colon in front of this line

    G1 X10.1 Y20 Z0.28 F5000.0 ;Move to start position

    G1 X10.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line

    G1 X10.4 Y200.0 Z0.28 F5000.0 ;Move to side a little

    G1 X10.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line

    G92 E0 ;Reset Extruder

    G1 Z2.0 F3000 ;Move Z Axis up

    Edited by GregValiant
  • Link to post
    Share on other sites

    Posted (edited) · problème avec la machine creality CR-10 Max -

    Merci ! 

    Je m'en vais sur un autre topic alors 🙂

     

    Edited by valentinehd
  • Link to post
    Share on other sites

    Posted · problème avec la machine creality CR-10 Max -

    Remove the build surface.  Give it a good bath with dish soap and water.

    Put the build surface back on.  Wipe it well with Isopropyl Alcohol 90% with a cloth that does not leave lint.

  • Link to post
    Share on other sites

    Posted · problème avec la machine creality CR-10 Max -

    réglage du plateau surement

     

    trouve un forum créality pour savoir comment faire

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • Introducing Universal Cura Projects in the UltiMaker Cura 5.7 beta
        Strap in for the first Cura release of 2024! This 5.7 beta release brings new material profiles as well as cloud printing for Method series printers, and introduces a powerful new way of sharing print settings using printer-agnostic project files! Also, if you want to download the cute dinosaur card holder featured below, it was specially designed for this release and can be found on Thingiverse! 
          • Like
        • 10 replies
      • S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
        (Sorry, was out of office when this released)

        This update is for...
        All UltiMaker S series  
        New features
         
        Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
          • Like
        • 0 replies
    ×
    ×
    • Create New...