Jump to content

Hotend fängt an zu Rauchen


coruscant-city

Recommended Posts

Posted · Hotend fängt an zu Rauchen

Mein Ultimaker Original stand ca 6 monate ohne Nutzung. Gestern sollte er wieder mal einen Auftrag erledigen, habe Ihn daher auf PLA vorgeheizt.

Die Temperatur des Fühlers und der Anzeige blieb lt Anzeige bei 200 Crad, aber nach einigen Minuten fing das Hotend an zu Rauchen, bzw dicker grauer Qualm stieg auf.  Die Temperaturanzeige zeigte an das die 200 Crad gehalten werden.. zumindest lt der Temperatursonde und der Anzeige. ... Ein Infrarottermomenter zeigte aber 310 Crad an und stieg weiter. Den Drucker habe ich dan logischerweise ausgeschaltet.

 

Hatte schon nen defekten Temperaturfühler dass dieser auf dem Dispaly nichts anzeigt, aber die Anzeige ist da.

 

Kennt jemand das Problem? Könnte mir noch vorstellen dass die Regelung am Mainbaord defekt ist und diese immer weiter Saft auf die Heizpatrone gibt... aber warum bleibht der Fühler dann auf 200 Crad fixiert. Bin daher nun etwas ratlos.  Kann mir da jemand einen Tip geben was es sein könnte oder wie ich mein Problem lösen könnte?

  • Link to post
    Share on other sites

    Posted · Hotend fängt an zu Rauchen

    Ich habe das schon von zwei Prusa MK3s gehört. Ein Bekannter hatte auch schon das Problem. Das ist unglaublich kritisch und wird auch durch thermal runaway nicht abgesichert. Liegt vermutlich am Board und nicht am Thermistor. 

    Bei dem prominenten Fall ist damals auch as Hotend geschmolzen: 

     

  • Link to post
    Share on other sites

    Posted · Hotend fängt an zu Rauchen

    Versuch mal den Temperatursensor am Mainboard abzuklemmen, und schau dann mal was für eine Temperatur angezeigt wird. Es sollte eine sehr niedrige Temp. angezeigt werden. Dann wäre der Sensor, oder seine Verkabelung defekt.

    Bleibt die Temp. weiterhin bei 200° stehen, ist das Mainboard defekt.

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • Introducing Universal Cura Projects in the UltiMaker Cura 5.7 beta
        Strap in for the first Cura release of 2024! This 5.7 beta release brings new material profiles as well as cloud printing for Method series printers, and introduces a powerful new way of sharing print settings using printer-agnostic project files! Also, if you want to download the cute dinosaur card holder featured below, it was specially designed for this release and can be found on Thingiverse! 
          • Like
        • 10 replies
      • S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
        (Sorry, was out of office when this released)

        This update is for...
        All UltiMaker S series  
        New features
         
        Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
          • Like
        • 0 replies
    ×
    ×
    • Create New...