Jump to content
Ultimaker Community of 3D Printing Experts
  • Sign Up
Sign in to follow this  
bill-havins

Cura 14.01 and Dual Hotend Prints On Rostock MAX

Recommended Posts

Posted · Cura 14.01 and Dual Hotend Prints On Rostock MAX

Please accept my apologies if this has been covered before.

I have adapted my Rostock MAX for dual hotend printing. I am using a Rambo 1.1 running a variant of Repetier Firmware 0.83 (adapted for the Rostock MAX).

In Cura 14.01 I have discovered an interesting "quirk." As one might imagine, I set up my machine settings including the appropriate offset for my second hotend/extruder (T1).

When one sets up a printer with two hotends/extruders Cura automatically offers templates for start/end code. In the start code the Z height is brought to a certain level and then both extruders are "primed." The second extruder (T1) is primed before the first extruder (T0). This leaves the first extruder ready to print when the main body of the g-code executes.

Here's the "quirk." If you choose to print a "raft" under your print you would expect the raft to print using the extruder you designated for support material (in my case, T1 - my second extruder). The layers depicted in the GUI indicate that that is exactly what will happen. But that is not what happens when the print actually runs. T0 is used to print the raft.

Now, you might think you could simply go into the g-code and insert a few lines of code (three, actually) to cause T1 to print the raft. But that can't be done because of T1's offset - if the raft is printed with T1 the raft print will be "off" by the amount of T1's offset. Oops!

So, the moral of the story is, T0 will print the raft in spite of what you see in the GUI.

Here's another interesting "need." If one is printing with, say ABS, and using, say, HIPS for support material. The "unified" retraction settings in 14.01 may leave one filament "starved" for material. So far in my experience ABS has seemed to require a greater amount of retraction than HIPS. If you optimize the retraction settings for ABS the HIPS portion of the print will be "starved." So there is a need to strike a compromise that causes some problems.

I have tried 14.02_RC5 but it tends to want to hang up and freeze on my Windows 7 64-bit computer. So for now I am running Cura 14.01.

Thanks to Daid for all of his hard work! Despite the above I still prefer Cura to other slicers that are available.

Bill

 

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

  • Our picks

    • Talking additive | The 3D printing podcast
      Why should we be the only ones asking questions? Join us and ask Jabil all your questions on September 22nd 5pm CET
        • Like
      • 2 replies
    • Ultimaker masterclass: Optimizing your Ultimaker Cura workflow
      Save your seat for either broadcast on September 23.
      What will you learn?
      · Best practices for iterative print preparation and every lesson you should learn from each print
      · The right way to use per-object settings and when they are most useful
      · Easy-to-use resources for anyone who wants to develop their own printer definitions, plugins, or print profiles
      · How to optimize print profile settings and whether to “keep” or “discard” changes
      · When is the right time to export your drawing from CAD? (Based on Ultimaker Cura’s surprising power as 3D control software)
      · And a whole lot more tips and tricks!
       
      How can I join?
      This free masterclass will take place twice:
      1. 11am CEST (5pm SGT, 5am EDT)
      2. 5pm CEST (11am EDT, 8am PDT, 11pm SGT)
        • Like
      • 0 replies
    • Do you use 3D printing at work? Let us know
      It doesn't matter if you are using 1 Ultimaker or 10, there is inspiration in everything. We're looking for ...
      • 1 reply
×
×
  • Create New...