Jump to content
Ultimaker Community of 3D Printing Experts

Recommended Posts

Are other people seeing quite a good amount of belt wear? Iv been cleaning little black flakes and dust off my machine quite a bit since getting it. Iv looked at the belts and you can see a bit of wear on the edges. Was wondering if others are seeing the same?

  • Link to post
    Share on other sites
    i dont have one yet BUT if this belt broke, where can we get replacement parts ?

    i dont see them for sale on the ultimaker website ?

    what would a new belt cost ?

    The so called MXL timing belts should be available world wide, just google "240 mxl belt" and "80 mxl belt" (1/4in wide), and you should find plenty of sources (about $4 each)

    joergen

  • Link to post
    Share on other sites
    i dont have one yet BUT if this belt broke, where can we get replacement parts ?

    i dont see them for sale on the ultimaker website ?

    what would a new belt cost ?

    Ian :D

    If you need replacement parts, best is to mail them. They dont sell it (yet) on the website.

  • Link to post
    Share on other sites

    One of my short belts has signs of wearing on edges. As Daid said it was caused by pulleys - just a few hours of printing with unaligned pulleys left visible marks.

  • Link to post
    Share on other sites
    One of my short belts has signs of wearing on edges.

    I have some wear on my short Y-belt too which I just noticed yesterday. The machine started to make some strange sounds in particular parts of the printing area. It appeared to be the damaged sides of the belts touching the pulley. I'll look after the alignment of the pulleys.

    Other than that my belts look fine.

  • Link to post
    Share on other sites

    Oh man, the spam is starting to get entertaining.

  • Link to post
    Share on other sites

    At least the bot made an attempt to stay on topic.

    I don't know if I should be happy or terrified about that...

  • Link to post
    Share on other sites

    Where can I get Gucci belt for my Ultimaker?

    240 mxl Pls.

    [EDIT]-> (Chinese knockoffs OK)

    [EDIT #2] And a fashionable handbag to put my screwdrivers etc in, (other forum members will be so jealous when they see it)

  • Link to post
    Share on other sites

    Get the flexible PLA and print your own fancy Gucci belt replacements?

    Note: I don't think flexible PLA will work as belts, because normal belts contain reenforcements so it doesn't stretch. You might be able to print timing belts with flexible PLA if you put thin steel cable in it during the print...

  • Link to post
    Share on other sites

    Forgive my ignorance but from what I've seen the pitch for an UM belt is 2.03mm, the one I will be using is 2mm spot on. My next question is about the pulleys and their size and number of teeth. Since the pulleys are different I want to make sure I get the same amount of linear travel per full rotation as the original UM.

    Any chance I can change that in the software if I can't get the right ratios?

  • Link to post
    Share on other sites

    Yes, you can adjust the firmware to get the correct movement.

  • Link to post
    Share on other sites

    You can help your belts to live longer by giving all your pulley wheels a proper deburring before building the

    machine (yes I know sorry not very useful advice once its all together). The standard pulleys have two pressed on

    discs at each side to stop the belt slipping off. Because these are obviously made with cost as the #1 priority, these discs are not deburred at all (a burr is a sharp edge caused from manufacturing). So if you dont remove all these edges from the belt alignment discs, they will sit and happily chew away at the edges of your belts. This will become much worse if you have any belt misalignment as then the belt will really be pushed against the sharp edges of the discs on the side of each pulley.

    So buy a proper deburring tool set, or just use the edge of a blade to remove all sharp edges from your pulley guide discs. This will help a great deal.

    Regards

    Calum

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    ×
    ×
    • Create New...