Jump to content
Ultimaker Community of 3D Printing Experts

Post your latest print!


Recommended Posts

Posted · Post your latest print!

Another dual extrusion test http://www.thingiverse.com/thing:647840. Scaled to 40%, blue and orange PLA, layer height 0.12mm, printing time 58 min.

Temp some degrees too high, especially for the orange.

This one is not really optimized for dual extrusion. Scaled down like that, the orange surface is shallow (0.8mm, you almost can see the blue shining through) and consists of tiny bits, virtually just blobs of filament.

gallery_5589_458_420536.jpg

 

  • Link to post
    Share on other sites
    • Replies 4.7k
    • Created
    • Last Reply

    Top Posters In This Topic

    Top Posters In This Topic

    Popular Posts

    Took me forever to do this. And it is still rougher than I would have liked.   3D concept rendering:   Finished piece:    

    Bath interferometers.  I have made about 20 of these for people who use them to test their telescope mirrors.  They are amazingly accurate and can do better than a $40,000 Zygo PSI optical tester.  Th

    I just finished this. It was a multi-part print for ease of painting. Some of it I am not sure what happened...but hey, it is purty....And, I am unanimous in that ? Test Render Parts

    Posted Images

    Posted · Post your latest print!

    Ok so here is my latest bust test using Autodesks Momento, using my crappy phone camera for the 51 photos. It came out pretty good, much more detailed than Catch123, but more separation issues from the background as it looked more complete in 123, but for a first attempt not too shabby. Printed in 0.1 colorfabb red PLA 222C 50mm/s.

    make sure you sit still...and use a camera with a real fast shutter for better results!

    Only available on pc at the mo from what ive seen, and yes its free as well...

    face.jpg

    image upload

     

  • Link to post
    Share on other sites
    Posted · Post your latest print!

    LOL I had the feeling something was not right here

     

  • Link to post
    Share on other sites
    Posted · Post your latest print!

    ha! got me too, nearly made it to my search bar before I thought better of it ;)

    printed for a buddy, 6 hours on the platform, blue LED on a post mounted thru the base w simple switch and a few AA's

    11055532_1570161353237957_1426543219_n.jpg

    11111364_815774048476720_1686054815_n.jpg

     

  • Link to post
    Share on other sites
    Posted · Post your latest print!

    IMG_1194-my3dsystems-print.jpg

    and then:

    _DSC7166-ultimaker2-printer-1600.jpg

    Used a glue stick, holds nicely for now.

     

  • Link to post
    Share on other sites
    Posted · Post your latest print!

    This should be the last bi-colored animal for some time ...

    I wanted to see if I can meet this benchmark http://www.thingiverse.com/make:106961

    gallery_5589_458_131579.jpg

     

  • Link to post
    Share on other sites
    Posted · Post your latest print!

    What size is that? It looks really good, even the print lines are hard to spot.

    This dual extrusion thing might finally actually happen :D

     

  • Link to post
    Share on other sites
    Link to post
    Share on other sites
    Posted · Post your latest print!

    OK i needed a Gold Cannes logo for something, so.....

    20150331_222625.jpg

    capture screen

     

    20150401_143208.jpg

    image upload no ads

    20150402_082958.jpg

    screenshot program

     

  • Link to post
    Share on other sites
    Posted · Post your latest print!

    nice result m8!

    Will you share the process you used to paint this?

     

  • Link to post
    Share on other sites
    Posted · Post your latest print!

    Just a touch of sanding and acetone and a touch more light sanding and undercoat then three to four light coats of metalic gold chrome. Didnt take too long. Might want to varnish or seal it after as the gold i used wore out a bit when i rubbed it. You can check my acetone smoothing pla thread for more pics.

  • Link to post
    Share on other sites
    Posted · Post your latest print!

    I finally decided to try out the Tree Frog that I have seen heaps of other people print and see how well my new fan shroud that I designed works. Not bad for a first attempt.

    Tree Frog Keyboard

    Tree Frog Finger

     

  • Link to post
    Share on other sites
    Posted · Post your latest print!

    I wouldnt even dare to try that :O

    Nice job!

     

  • Link to post
    Share on other sites
    Posted · Post your latest print!

    What nozzle are you using Labern?

     

  • Link to post
    Share on other sites
    Posted · Post your latest print!

    0.25mm on the Olsson Block from 3d solex

  • Link to post
    Share on other sites
    Posted · Post your latest print!

    Nice prints guys :)

    This is the same gcode printed twice with a 0.8mm nozzle and layers of 0.2mm

    Left, bronzeFill sanded and polished by hand, right BambooFill covered with some oil for wood (Osmo oil).

    20150403 123916

     

    No problems at all with the .8mm nozzle for bronzefill, and bambooFill prints very nicely too

     

  • Link to post
    Share on other sites
    Posted · Post your latest print!

    @didier, that's a surprisingly nice result for 0.8/0.2 !

     

  • Link to post
    Share on other sites
    Posted · Post your latest print!

    I've noticed that bronzefill doesn't really care. I've been printing at 0.6/0.2. As soon as you sand it a bit, all the layers are gone anyway!

     

  • Link to post
    Share on other sites
    Posted · Post your latest print!

    Yep and Woodfill is nice too with big layers :)

    I'm pretty sure you can have a nice result too with .3mm layers with both of them. And also that you can avoid blocked nozzzles with a .8mm nozzle and wood filaments

     

  • Link to post
    Share on other sites
    Posted · Post your latest print!

    Can you post a picture before the sanding?

     

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now

    • Our picks

      • Startups, apply for the Forward AM Innovation Award!
        Are you a startup using 3D printing? Perhaps you should continue reading... 
         
        Together with BASF we are launching the Forward AM Innovation Award - the very first global contest for startups developing new applications with 3D printing!
         
        Why apply?
        The winning startup will receive €100,000 in goods and services*, along with coaching and marketing exposure from top-notch leaders in the industry.
         

         
        Who can apply?
        Your startup creates products using Additive Manufacturing, is less than 5 years old, and has less than 50 employees. We are looking for 3D printing applications with a strong focus on innovation, sustainability and scalability.
         
        Dental aligners, shoes, tools, automotive parts, music instruments, industrial tooling and molding, medical implants, sports equipment, toys, architecture, fashion, construction... all are welcome to join!
         
        Do you have an innovative, sustainable and scalable idea that leverages the unique possibilities of 3D printing? Then it is time to apply!
        More information can be found here.
         
        Applications close on March 28th, 2021
        * What does "in goods and services" mean?
        The winner will be able to pick any item from the overall product and service portfolio of the sponsors, e.g. printers, materials, consulting, software... Choose whatever you need to accelerate your startup.
         
          • Like
        • 0 replies
      • New here? Register your Ultimaker for free 3D printer onboarding course
        Hi,
         
        Often getting started is the most difficult part of any process. A good start sets you up for success and saves you time and energy that could be spent elsewhere. That is why we have a onboarding course ready for
        Ultimaker S5 Pro Bundle, Ultimaker S5, Ultimaker S3 Ultimaker 2+ Connect.   
        They're ready for you on the Ultimaker Academy platform. All you need to do to gain access is to register your product to gain free access. 
        Ready? Register your product here in just 60 seconds.
          • Like
        • 0 replies
    ×
    ×
    • Create New...