Jump to content
anon4321

Disabling USB Power because my memory is CRAP!

Recommended Posts

Posted · Disabling USB Power because my memory is CRAP!

You may have noticed especially if you have the ulticontroller that the electronics will be powered by the USB cable if you switch the primary power off.

The problem is that I believe the ulticontroller draws more current than the arduino's USB power source can supply. This causes the resettable fuse on the arduino to kick in and cut the current only to reset and kick in again over and over.

I see this as the ulticontroller to pulse or blink.

As I'm old and my memory is crap this was a regular occurrence.

******** WARNING: YOU CAN DAMAGE YOUR ARDUINO PERFORMING THIS MOD ********

******** DO THIS MOD AT YOUR OWN RISK *******

******** IM NOT SURE THIS IS A VALID WAY TO DO THIS BUT IT WORKS FOR ME ********

After doing this, turning off the UM1 with the power switch causes everything to power off and the COM port disappears on the PC.

Here is how to PERMANENTLY prevent the arduino mega 2560 R3 from drawing power from the USB connector.

disable Usb power notes

Unmodified vs. modified:

 

First pic without annotations.

 

 

Share this post


Link to post
Share on other sites
Posted · Disabling USB Power because my memory is CRAP!

I like the idea, But not the way to develop it,

Isn't there any software way to develop that?

PD: that Usb power, as someone told me(I don't know if it is true), can damage your computer PSU.

 

Share this post


Link to post
Share on other sites
Posted · Disabling USB Power because my memory is CRAP!

That mod disconnects the 5v line in the USB cable from the arduino so it is actually less likely to damage your computer. All the other protections built into the arduino still work and protect your PC.

The jumper is required to take the onboard 5V to the ATMEGA16. I checked the ATMEGA's datasheet and this is how self powered (as opposed to USB powered) .configurations are done.

I'm fairly sure that this mod won't hurt your PC but ANYTHING you do with respect to this type of mod has RISK So don't do it if you don't understand it.

 

Share this post


Link to post
Share on other sites
Posted · Disabling USB Power because my memory is CRAP!

PD: that Usb power, as someone told me(I don't know if it is true), can damage your computer PSU.

 

If that is the case, then your motherboard producer is at fault. The USB specification specifically talks about protecting against this.

 

Share this post


Link to post
Share on other sites
Posted (edited) · Disabling USB Power because my memory is CRAP!

I know this thread is old but I'm trying to solve the same problem a.t.m.

My question is: Why have you chosen that way?

Woudn't it be more easy to just desolder the MOSFET that is between the USBVCC and the +5V on the board?

5a3310f2505bc_mosfetjumper.thumb.PNG.93a1f7f9ec59ffc7329224956f808094.PNG

It will still power the ATMEGA16 this way but not the remaining board.

5a3310f264743_mosfetjumperboard.thumb.PNG.ef89b2a0bba508d2b72602279f495cfc.PNG

And VIN does still power the board as before:

5a3310f2ba092_mosfetjumperVIN.thumb.PNG.febcbace56820d6fc5765b6c273c5630.PNG

Can anyone confirm my thoughts? (maybe @anon4321)

Thanks ;)

5a3310f2505bc_mosfetjumper.thumb.PNG.93a1f7f9ec59ffc7329224956f808094.PNG

5a3310f264743_mosfetjumperboard.thumb.PNG.ef89b2a0bba508d2b72602279f495cfc.PNG

5a3310f2ba092_mosfetjumperVIN.thumb.PNG.febcbace56820d6fc5765b6c273c5630.PNG

Edited by Guest

Share this post


Link to post
Share on other sites
Posted (edited) · Disabling USB Power because my memory is CRAP!

Well, I tried it now - it works like a charm if you just desolder the MOSFET FDN340P near the Polyfuse ;)

5a3310f72297c_removeMOSFET.thumb.png.208ce055613ac894771eb3e46b11a400.png

5a3310f72297c_removeMOSFET.thumb.png.208ce055613ac894771eb3e46b11a400.png

Edited by Guest
  • Like 1

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Our picks

    • Ultimaker Cura 4.0 | Stable available!
      Ultimaker Cura 4.0 is mainly focused on the improved user interface and cloud integration.
      As always, we want to collect your user feedback for this release. If there are any improvements you can think of, feel free to mention it here and help us to shape the next release.
      • 23 replies
×
×
  • Create New...

Important Information

Welcome to the Ultimaker Community of 3D printing experts. Visit the following links to read more about our Terms of Use or our Privacy Policy. Thank you!