Jump to content
Ultimaker Community of 3D Printing Experts

Paint visibly absorbs into prints. Suggestions appreciated.


Recommended Posts

Posted · Paint visibly absorbs into prints. Suggestions appreciated.

Hello all. As a hobby I sell custom 3D printed dice. I hand-paint the numbers. However, sometimes the paint visibly absorbs between the layers of plastic in some parts of the prints. This only happens in some areas. Just wondering if anyone has any suggestions. Any printing preferences suggestions? Do you think a quick spray clear coat of some sort would help?

 

  • Link to post
    Share on other sites
    Posted · Paint visibly absorbs into prints. Suggestions appreciated.

    I guess that you can't prime unless doing it by hand as well as i supose you only want to paint the numbers and use plastic only on the rest of the dice.

    By the way, do you use brush or some kind of a marker.

    If using a marker i think it can be hard as the paint is extreamly thin.

    If using a brush and a little thicker paint i think the problem might be bad bonding between layers. Make sure thay you dont have under extrusion problems and if not, try to print a little hotter.

  • Link to post
    Share on other sites
    Posted · Paint visibly absorbs into prints. Suggestions appreciated.

    primer would definately help, but might not solve it completely if your paint is too runny.

    Try not thinning your paints, or get some thicker stuff, they shouldn't do the capillary thing as much.

    Or, for a better result, emboss the numbers into the geometry of your print. It'll make painting easier, you can even sand off the surface after putting paint in for a really nice clean finish!

     

  • Link to post
    Share on other sites
    Posted · Paint visibly absorbs into prints. Suggestions appreciated.

    Strange. I use standard Humbrol enamels. They do just as well as on any plastic model you can find in a hobby shop.

    Airbrush or by hand - very good results. I even tried a test without a primer - worked, too.

     

  • Link to post
    Share on other sites
    Posted · Paint visibly absorbs into prints. Suggestions appreciated.

    Use primer.

    I use SEM primer/surfacer.

    Prime then sand to give it a smooth surface, and paint.

     

  • Link to post
    Share on other sites
    Posted · Paint visibly absorbs into prints. Suggestions appreciated.

    I'm assuming he only wants to paint the detail onto the part, and not cover the colored PLA with grey primer.

    Look into trying this solvent to seal the parts before painting them. I've used MEK for PLA, but its quite hazardous and not that effective.

    https://groups.google.com/forum/#!topic/makerbot/wXZ5HyqOa6I%C2%A0

     

  • Link to post
    Share on other sites
    Posted · Paint visibly absorbs into prints. Suggestions appreciated.

    I already have numbers embossed. I was just curious if anyone else noticed this issue. Will attempt higher temperature.

     

  • Link to post
    Share on other sites
    Posted · Paint visibly absorbs into prints. Suggestions appreciated.

    I am wondering if it might be a result or poor layer adhesion. What is the size of the dice and what settings do you use? Oops I see an earlier post raised this too - anyway question remains.

     

  • Link to post
    Share on other sites
    Posted · Paint visibly absorbs into prints. Suggestions appreciated.

    about and inch cubed. Or 25 mm cubed for you metric folk. I print at .17mm layers @ 225 degrees C.

     

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • 16 Visiting our virtual showroom

      1. 1. Have you visited our virtual showroom before?


        • Yes
        • No
      2. 2. If yes - what content did you find most interesting?


        • Information about Ultimaker ecosystem
        • Applications & application stories
        • Customer success stories
        • Webinar sessions
        • Material wall & ecosystem partners
        • New product introduction; software subscription plans
      3. 3. What of the below would make you consider visiting (again)?


        • New Live Ultimaker Webinar streams
        • ‘Ask Me Anything’ with industry experts or Ultimaker staff via main stage and public chat
        • New customer success stories
        • New applications
        • Presentations/news from ecosystem partners
        • Opportunity to meet representatives for an interactive tour
        • Helpful videos like Software tutorials
        • Other; leave input in a comment below!

    • Our picks

      • Ultimaker turns 10: A look back
        Ultimaker is turning 10 years old and that means it is story telling time! We'll explore 2010-2014, traveling through the evolution of the business from the Protobox and Ultimaker Original, to the major leaps forward with the Ultimaker 2 and Ultimaker 3.
          • Like
        • 0 replies
      • Ultimaker Transformation Summit
        Visit our virtual showroom and learn more about the Ultimaker ecosystem!
        • 14 replies
      • New here? Register your Ultimaker for free 3D printer onboarding course
        Hi,
         
        Often getting started is the most difficult part of any process. A good start sets you up for success and saves you time and energy that could be spent elsewhere. That is why we have a onboarding course ready for
        Ultimaker S5 Pro Bundle, Ultimaker S5, Ultimaker S3 Ultimaker 2+ Connect.   
        They're ready for you on the Ultimaker Academy platform. All you need to do to gain access is to register your product to gain free access. 
        Ready? Register your product here in just 60 seconds.
          • Like
        • 0 replies
    ×
    ×
    • Create New...