Jump to content
Ultimaker Community of 3D Printing Experts

Highest resolution you've printed?


Recommended Posts

Posted · Highest resolution you've printed?

Hi I'm just interested to see what the highest resolutions people have been printing successfully with the Ultimaker printers, I know they say that v2 can print 20 microns but what have prints turned out like printed like that? Very interested to hear.

 

  • Link to post
    Share on other sites
    Posted · Highest resolution you've printed?

    Your resolution is limited more by nozzle radius (limits X,Y resolution) than by Z. This is true on all of these FDM printers (printers that heat plastic through a nozzle). The nozzle hole diameter on UMO and UM2 is .4mm (radius .2mm) so .2mm radius curve is the tightest corner you can make on the 4 vertical edges of a cube. The top and bottom 8 edges are not limited by nozzle but by layer height as you say. Still most of the model is limited by XY more than Z.

    If you look at make magazine's recent report on similar 3d printers, the UM2 came out on top of all the other printers.

    http://cdn.makezine.com/make/magazine/V42-preview.pdf

     

  • Link to post
    Share on other sites
    Posted · Highest resolution you've printed?

    I did one or two test prints at 20um early on and they turned out ugly, fuzzy, etc. I didn't think it was worth trying to improve it because trying to get that sort of resolution out of this type of machine is basically a waste of time: it takes forever and just isn't worth it for anything I've seen.

  • Link to post
    Share on other sites
    Posted · Highest resolution you've printed?

    Printing at lower Z resolution is much more difficult than at higher.

    Here are some factors:

     

    Size of the object is important, if it is small then there is not sufficient cooling time

    before layers, again depending on your minimal layer time, and

    the initial buildplate height also plays a part, more at low levels/thin models.

    Frequently people adjust the buildplate too close.

    Personally I adjust by eye only, and when using a 0.4mm head i

    adjust from "nozzle touching glass plate" and "3 clicks down" in the inner point.

    Then I adjust by eye only the left and right screws, tapping the buildplate from below to

    see that there is a movement.

    If the distance is too close it is more of a problem with next layer nozzle move digging into

    the previous layer.

    If it is too big, lets say more than 0.5mm (with 0.4 nozzle) then the only issue may be

    1st layer not sticking so well. But if you pass THAT obstacle, then height "adjusts itself" in the

    "setting" of the first coupl'a layers, and prints better.

    Also, like the old foxes in this forum always re-iterate; print slowly.

    Remember; if you keep 50mm/s in Cura ( I do and most others ), then

    the speed setting in UM2 at 100% gives you just that, 50mm/s.

    We call this speed setting in UM2 a "modifier".

    When you keep Cura at 50, (advised), then putting UM2 at 80% calculates like this:

    50mm/s (from Cura) x 80% (from UM2) = 40mm/s speed.

    Quality of material is also an important factor.

    I have printed a lot of different material. From aliexpress, from ebay, from other sources.

    I find that the PLA i bought from Ultimaker is absolutely top class (I am in no way affiliated with them).

    There are different characteristics in solidifying speed, temperatures, thickness, foreign particles, etc..

    Many problems go away when you print quality PLA at 220, height 0.2, 30-50mm/s effective speed, and use the

    Atomic Method between all material changes and even more frequently.

    : TinyDancer is confirming what many others have found, that Z axis resolution is not the most important

    factor.

     

     

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • Startups, apply for the Forward AM Innovation Award!
        Are you a startup using 3D printing? Perhaps you should continue reading... 
         
        Together with BASF we are launching the Forward AM Innovation Award - the very first global contest for startups developing new applications with 3D printing!
         
        Why apply?
        The winning startup will receive €100,000 in goods and services*, along with coaching and marketing exposure from top-notch leaders in the industry.
         

         
        Who can apply?
        Your startup creates products using Additive Manufacturing, is less than 5 years old, and has less than 50 employees. We are looking for 3D printing applications with a strong focus on innovation, sustainability and scalability.
         
        Dental aligners, shoes, tools, automotive parts, music instruments, industrial tooling and molding, medical implants, sports equipment, toys, architecture, fashion, construction... all are welcome to join!
         
        Do you have an innovative, sustainable and scalable idea that leverages the unique possibilities of 3D printing? Then it is time to apply!
        More information can be found here.
         
        Applications close on March 28th, 2021
        * What does "in goods and services" mean?
        The winner will be able to pick any item from the overall product and service portfolio of the sponsors, e.g. printers, materials, consulting, software... Choose whatever you need to accelerate your startup.
         
          • Like
        • 0 replies
      • New here? Register your Ultimaker for free 3D printer onboarding course
        Hi,
         
        Often getting started is the most difficult part of any process. A good start sets you up for success and saves you time and energy that could be spent elsewhere. That is why we have a onboarding course ready for
        Ultimaker S5 Pro Bundle, Ultimaker S5, Ultimaker S3 Ultimaker 2+ Connect.   
        They're ready for you on the Ultimaker Academy platform. All you need to do to gain access is to register your product to gain free access. 
        Ready? Register your product here in just 60 seconds.
          • Like
        • 0 replies
    ×
    ×
    • Create New...