Jump to content
Ultimaker Community of 3D Printing Experts

Recommended Posts

Posted · Quality/calibration?

I made my first few prints, using Cura. (for what it's worth: I was unable to complete the check routine, it stopped after the message for moving the head to the middle)

The quality is not yet at the level where I want it, any suggestions? (sorry for picture rotation...)

1) Flat surfaces (bottom layers or on top of a 30% fill) don't seem to fill entirely, like it doesn't extrude enough material.

Img3356.thumb.jpg.4ca08af9d0c2471869e3b90d23e7fdea.jpg

2a) Sometimes suddenly gaps appear. Some close after a few layers, others end the exercise (note that these are single walls, 0.4mm, no fill)

2b) 0.1mm layer height looks a bit smeared, quality is almost worse than 0.2mm!

Cura-UM2.thumb.png.4a3afc7c9fe6bd8914b68c98b1f2dea9.png

um2go-box.thumb.jpg.2018f86f7a4341c4d8385c9f3d77a9db.jpg

  • Link to post
    Share on other sites
    Posted · Quality/calibration?

    At what temperature are you printing?

    Is your filament tension knob thigh enough?

    What was the value you got for the "steps per E" calibration?

  • Link to post
    Share on other sites
    Posted · Quality/calibration?

    Temperature: 210C

    Knob is tight enough, but that's hard to check of course (it leaves clearly visible marks on the filament).

    The filament is PLA from Ultimaker, could it be the quality (varying thickness)?

    Steps per E had to be adjusted a little bit higher: 872.870967742 (it extruded 99.2mm)

  • Link to post
    Share on other sites
    Posted · Quality/calibration?

    It looks like you are under-extruding, so not enough material is coming out.

    210C should be fine, but you could up it to 230C to see if that prints better.

    Check the actual filament diameter versus the configured diameter. Measure the filament on multiple locations to get a good average. (Some UM PLA is found to be quite thin)

    872.8 is fine for the steps per E.

    The knob usually can be tighter, it should leave clear marks in the filament, with light marks it can still skip.

    Another thing I use to check tension of the knob:

    During printing, put your finger below the input of the PLA, below the big gear, on the filament. This way you can feel the filament being pulled into the drive mechanism. If you do this then you can feel if it slips, because when it slips it will pull back a bit or the speed at which it is pulled in is uneven.

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • Ultimaker Transformation Summit
        Visit our virtual showroom and learn more about the Ultimaker ecosystem!
        • 14 replies
      • New here? Register your Ultimaker for free 3D printer onboarding course
        Hi,
         
        Often getting started is the most difficult part of any process. A good start sets you up for success and saves you time and energy that could be spent elsewhere. That is why we have a onboarding course ready for
        Ultimaker S5 Pro Bundle, Ultimaker S5, Ultimaker S3 Ultimaker 2+ Connect.   
        They're ready for you on the Ultimaker Academy platform. All you need to do to gain access is to register your product to gain free access. 
        Ready? Register your product here in just 60 seconds.
          • Like
        • 0 replies
    ×
    ×
    • Create New...