Jump to content
Ultimaker Community of 3D Printing Experts

Board game spinner


Recommended Posts

Posted · Board game spinner

This is my latest, I use it as a bit of a test print at the moment because I'm trying to make it work :)

It's one of those spinners you use in board games like Articulate, which we inevitably break after playing enough times, because you have to flick them pretty hard.

You can't tell from this print, but the pillar in the centre has a narrow portion (2.2mm) and a slightly larger knob on the top (2.3mm).

This one was done with Cura at 0.15 layers, which had a problem with the thin portion of the pillar, too much plastic coming out.

A few questions for the more knowledgeable:

1 - It's hard to tell, but the 'from above' picture shows that the two halves of the large circle are not directly aligned. Different slicers make no difference to this - Cura was better than KISSlicer - though I should rotate the model 90 degrees and try again to prove it's a model or slicing problem rather than a printer problem.

2 - too much goop in the pillar - I had a minimum flow limit set to 5mm (default?), perhaps that was the problem. Also of interest was the minimum layer time (10s), which seemed to be ignored for the pillar. Does anyone have any hints for tricks when moving from large areas of fill to small bits, as occurs in this case?

  • Link to post
    Share on other sites
    Posted · Board game spinner

    jcosmo,

    I don't see any "not aligned" error. The photograph could be better... Is the inside not touching the perimeter at some point? Belt tension.

    I think you're over-extruding. You told the software you have a 2.80 filament while in fact you have a 2.84 diameter filament.

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • 18 Visiting our virtual showroom

      1. 1. Have you visited our virtual showroom before?


        • Yes
        • No
      2. 2. If yes - what content did you find most interesting?


        • Information about Ultimaker ecosystem
        • Applications & application stories
        • Customer success stories
        • Webinar sessions
        • Material wall & ecosystem partners
        • New product introduction; software subscription plans
      3. 3. What of the below would make you consider visiting (again)?


        • New Live Ultimaker Webinar streams
        • ‘Ask Me Anything’ with industry experts or Ultimaker staff via main stage and public chat
        • New customer success stories
        • New applications
        • Presentations/news from ecosystem partners
        • Opportunity to meet representatives for an interactive tour
        • Helpful videos like Software tutorials
        • Other; leave input in a comment below!

    • Our picks

      • Ultimaker turns 10: A look back
        Ultimaker is turning 10 years old and that means it is story telling time! We'll explore 2010-2014, traveling through the evolution of the business from the Protobox and Ultimaker Original, to the major leaps forward with the Ultimaker 2 and Ultimaker 3.
          • Like
        • 0 replies
      • Ultimaker Transformation Summit
        Visit our virtual showroom and learn more about the Ultimaker ecosystem!
        • 14 replies
      • New here? Register your Ultimaker for free 3D printer onboarding course
        Hi,
         
        Often getting started is the most difficult part of any process. A good start sets you up for success and saves you time and energy that could be spent elsewhere. That is why we have a onboarding course ready for
        Ultimaker S5 Pro Bundle, Ultimaker S5, Ultimaker S3 Ultimaker 2+ Connect.   
        They're ready for you on the Ultimaker Academy platform. All you need to do to gain access is to register your product to gain free access. 
        Ready? Register your product here in just 60 seconds.
          • Like
        • 0 replies
    ×
    ×
    • Create New...