Jump to content
Ultimaker Community of 3D Printing Experts

Recommended Posts

Due to some critical problems, I want to move the 15.02 release very fast. So today or tomorrow.

Right now I have an RC2 at:

http://software.ultimaker.com/Cura_closed_beta/

The changes are:

* Fixed problem with SD saving on Mac and Linux

* Fixed problem with Cura not starting when you have "none ascii" characters in your username

* Fixed UM2 retraction at the end of a print

* Fixed UM2 priming after a filament change when pausing.

 

  • Link to post
    Share on other sites

    I had problems with imported SD material settings disappearing form the printer after power cycling: https://github.com/Ultimaker/Ultimaker2Marlin/issues/68

    Anyone else experienced this? (I recommend to back up your SD-file before playing with this, it is very easy so overwrite the file on the SD card by accident)

     

    This can happen if your imported settings put a value "out of range", this will trigger this code:

    https://github.com/Ultimaker/Ultimaker2Marlin/blob/master/Marlin/UltiLCD2_menu_material.cpp#L852

     

  • Link to post
    Share on other sites

    Hi, as you will be aware I'm new here!

    What is the latest release?

    Can someone please explain the difference between 15.02 RC2 and 15.02.1

    I have seen issues with 15.02.1 such as the filament retract issue on pause/abort, is this being fixed in RC2 which will later become 15.02.2?

    Many thanks

     

  • Link to post
    Share on other sites

    Hi, as you will be aware I'm new here!

    What is the latest release?

    Can someone please explain the difference between 15.02 RC2 and 15.02.1

    I have seen issues with 15.02.1 such as the filament retract issue on pause/abort, is this being fixed in RC2 which will later become 15.02.2?

    Many thanks

     

    The RC2 is the same as the 15.02.1 feature wise. The RC's are "release canidates" and thus are made before the actual release. Newer versions will be 15.03-RCx versions.

     

  • Link to post
    Share on other sites

    Daid, no hurry to fix this minor problem, but...

    I think you should erase the name on the main display bottom which tells what was saved last time on the SD card. Whenever you make some change to the parts or at least when you replace the plate with new parts, that message should be empty because it can be mistakenly understood as the current design has been saved with that name, which is not true.

  • Link to post
    Share on other sites

    Where am I going wrong.

    Since I went from Cura 14 to Cura 15 nothing prints properly.

    My 14 stuff is printing okay but anything I am slicing with either version of 15 is either doing a mass retraction and then not refeeding the filament when it goes back to printing.

    If it does refeed it carries on printing before the filament is back and just spools every where.

    I run a 14 Gcode and it is fine as I said so can't be the printer.

    I updated the firmware as well. If it does carry on dosen't retract it kind of jams on the last 2 or 3mm at the top. An just pumps a great ball of plastic onto the top of the print.

    I'm totally baffled.

    this might be in the wrong place.

    I don't know!

    15.02.01 not RC2. I don't know.

     

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • 18 Visiting our virtual showroom

      1. 1. Have you visited our virtual showroom before?


        • Yes
        • No
      2. 2. If yes - what content did you find most interesting?


        • Information about Ultimaker ecosystem
        • Applications & application stories
        • Customer success stories
        • Webinar sessions
        • Material wall & ecosystem partners
        • New product introduction; software subscription plans
      3. 3. What of the below would make you consider visiting (again)?


        • New Live Ultimaker Webinar streams
        • ‘Ask Me Anything’ with industry experts or Ultimaker staff via main stage and public chat
        • New customer success stories
        • New applications
        • Presentations/news from ecosystem partners
        • Opportunity to meet representatives for an interactive tour
        • Helpful videos like Software tutorials
        • Other; leave input in a comment below!

    • Our picks

      • Ultimaker turns 10: A look back
        Ultimaker is turning 10 years old and that means it is story telling time! We'll explore 2010-2014, traveling through the evolution of the business from the Protobox and Ultimaker Original, to the major leaps forward with the Ultimaker 2 and Ultimaker 3.
          • Like
        • 0 replies
      • Ultimaker Transformation Summit
        Visit our virtual showroom and learn more about the Ultimaker ecosystem!
        • 14 replies
      • New here? Register your Ultimaker for free 3D printer onboarding course
        Hi,
         
        Often getting started is the most difficult part of any process. A good start sets you up for success and saves you time and energy that could be spent elsewhere. That is why we have a onboarding course ready for
        Ultimaker S5 Pro Bundle, Ultimaker S5, Ultimaker S3 Ultimaker 2+ Connect.   
        They're ready for you on the Ultimaker Academy platform. All you need to do to gain access is to register your product to gain free access. 
        Ready? Register your product here in just 60 seconds.
          • Like
        • 0 replies
    ×
    ×
    • Create New...