Jump to content

Z Achse kalibrieren


diettelo

Recommended Posts

Posted · Z Achse kalibrieren

Hallo

Ich drucke seit ein paar Tagen mit dem Ultimaker 2 sehr gute Ergebnisse.

Doch plötzlich aus heiterem Himmel stimmt die Position zwischen Druckkopf und buildplate bei weitem nicht mehr. Ich meine nicht 2-3 mm sondern eher 3-4 cm. Er drückt in der Luft. Hab schon buildplate neu einstellen wollen selbes Ergebnis. Was kann da sein oder was muss ich machen? Ich kann unmöglich den Abstand mit den Schrauben korrigieren. Hab schon Factory Reset gemacht keine Besserung.

  • Link to post
    Share on other sites

    Posted · Z Achse kalibrieren

    Hallo diettelo

    Beim UM2 ist die Prozedur zur Ausrichtung des Druckbetts 2-Stufig.

    Im ersten Schritt fährt man elektrisch bis ca. 1 mm an den Druckkopf heran. Dazu wird der Drehknopf vorne am Drucker benötigt. In der 2. Phase folgt dann die Feineinstellung. Bei der Position hinten in der Mitte wiederum mit dem Drehknopf und einem Blatt Papier als Abstandstester. Dasselbe wird dann auch noch vorne links und rechts gemacht, ebenfalls mit Papier, aber dort werden die Schrauben gedreht. Das sollte mehr oder weniger logisch sein, wenn Du im Menü die Ausrichtung der Buildplate startest.

    Gruss, Obi

     

  • Link to post
    Share on other sites

    Posted · Z Achse kalibrieren

    Hallo,

    nur noch mal zum Abgleich des Vorgehens:

    Der Drehknopf wird doch nur benutzt für die hintere Position beim ersten Durchlauf.

    Bei allen anderen Positionen und beim zweiten Durchlauf werden nur die Rändelschrauben benutzt (und nicht der Drehknopf). Richtig?

    Grüße

    Marcus

     

  • Link to post
    Share on other sites

    Posted · Z Achse kalibrieren

    Der Drehknopf stellt auch den Abstand hinten beim 2. Durchgang ein.

    Erster Durchgang hinten ca 1mm per Knopf einstellen, vorne per Schraube. Zweiter Durchgang hinten gewünschten Abstand per Drehrad einstellen, vorne per Schraube.

  • Link to post
    Share on other sites

    Posted · Z Achse kalibrieren

    Hallo was macht dann der hintere schrauben habs beim 2ten mal ummer mit dem justiert.

    Was mich noch interessieren würde ist das manche Leute schreiben das man das heatbed als aufgeheizter justieren soll?

  • Link to post
    Share on other sites

    Posted · Z Achse kalibrieren

    Hmm, frag ich mich gerade auch. Ich kann mir vorstellen, dass sich das ganze Metallgerüst ja bei wärme ausdehnt. Nicht viel, aber bei 0,3mm Standartabstand beim ersten Layer vielleicht schon merkbar...

     

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
    • Our picks

      • Introducing Universal Cura Projects in the UltiMaker Cura 5.7 beta
        Strap in for the first Cura release of 2024! This 5.7 beta release brings new material profiles as well as cloud printing for Method series printers, and introduces a powerful new way of sharing print settings using printer-agnostic project files! Also, if you want to download the cute dinosaur card holder featured below, it was specially designed for this release and can be found on Thingiverse! 
          • Like
        • 10 replies
      • S-Line Firmware 8.3.0 was released Nov. 20th on the "Latest" firmware branch.
        (Sorry, was out of office when this released)

        This update is for...
        All UltiMaker S series  
        New features
         
        Temperature status. During print preparation, the temperatures of the print cores and build plate will be shown on the display. This gives a better indication of the progress and remaining wait time. Save log files in paused state. It is now possible to save the printer's log files to USB if the currently active print job is paused. Previously, the Dump logs to USB option was only enabled if the printer was in idle state. Confirm print removal via Digital Factory. If the printer is connected to the Digital Factory, it is now possible to confirm the removal of a previous print job via the Digital Factory interface. This is useful in situations where the build plate is clear, but the operator forgot to select Confirm removal on the printer’s display. Visit this page for more information about this feature.
          • Like
        • 0 replies
    ×
    ×
    • Create New...