Jump to content
Ultimaker Community of 3D Printing Experts

Massive problems using RepRap Flavor


wemarch
 Share

Recommended Posts

Posted · Massive problems using RepRap Flavor

Hi there,

we face the following problem here: in order to set the printing temperature in Cura we had to choose the RepRap G-Code flavour in the machine settings, which we thought should be no problem.

But it shows that this leads to a way too fast feeding speed. This means massive underextrusion and even "cutting" of the filament by the extruder motor.

It took a while until we found out, that this was because of the flavour settings, but with UltiGCode it works fine! Same problem using Slic3r because there is no "UltiGCode".

Does anybody else encounter that problem?

P.S.: We'd like to set the temperature (nozzle) in Cura because we do some testing with the yield strength at different printing temperatures.

 

  • Link to post
    Share on other sites

    Posted · Massive problems using RepRap Flavor

    When you switch to "rep rap" mode several settings in Cura suddenly appear:

    Nozzle Temp

    Bed Temp

    Filament Diameter

    Retraction distance

    Retraction speed

    I suspect the "filament diameter" setting is wrong. It should normally be 2.85. I'm printing on a UM2 as we speak in reprap mode and it works fine for me.

     

  • Link to post
    Share on other sites

    Posted · Massive problems using RepRap Flavor
    Which reprap mode do you use?

     

    *not* volumetric. Some printers evidently move the filament by volume but Marlin expects filament movements in mm, not mm^3.

     

  • Link to post
    Share on other sites

    Posted · Massive problems using RepRap Flavor

    *not* volumetric. Some printers evidently move the filament by volume but Marlin expects filament movements in mm, not mm^3.

     

    Except if you use the M200 commands to specify the proper filament diameter. Then Marlin expects the filament amount in mm^3. But it should only used together with the firmware retraction as you might get some mess otherwise.

     

  • Link to post
    Share on other sites

    Posted · Massive problems using RepRap Flavor

    *not* volumetric. Some printers evidently move the filament by volume but Marlin expects filament movements in mm, not mm^3.

     

    Thank you very much, that seems to be the sticking point. We used volumetric alle the time. I assume Marlin interpreted mm^3 as mm...

    Four weeks of error search just came to an end :-P . Thank you a lot!

    P.S.: This is why I used volumetric: http://umforum.ultimaker.com/index.php?/topic/6025-um-2-temperature/?p=60436

     

  • Link to post
    Share on other sites

    Posted · Massive problems using RepRap Flavor

    I added a note to that posting you link to. I think Eldrick has a UMO only so although he's pretty smart and usually gives good advice I think he goofed on that one [oh wait a correction to my correction - evidently volumetric is fine if you add an M200 command]. I had read his comment before and didn't notice the "volumetric" issue and even if I had I'm not sure I would have known that he was wrong at the time. But I have been using reprap mode quite a bit this week for a stretchlet project. I'm hoping to print 500 stretchlets.

     

  • Link to post
    Share on other sites

    Create an account or sign in to comment

    You need to be a member in order to leave a comment

    Create an account

    Sign up for a new account in our community. It's easy!

    Register a new account

    Sign in

    Already have an account? Sign in here.

    Sign In Now
     Share

    • Our picks

      • New here? Get ahead with a free onboarding course
        Hi,
         
        Often getting started is the most difficult part of any process. A good start sets you up for success and saves you time and energy that could be spent elsewhere. That is why we have a onboarding course ready for
        Ultimaker S5 Pro Bundle, Ultimaker S5, Ultimaker S3 Ultimaker 2+ Connect.   
        They're ready for you on the Ultimaker Academy platform. All you need to do to gain access is to register your product to gain free access. 
        Ready? Register your product here in just 60 seconds.
          • Like
        • 11 replies
    ×
    ×
    • Create New...