Jump to content

ryan-walks

Dormant
 View Profile  See their activity

  • Posts

    11

  • Joined

  • Last visited

    Never

 Content Type 

Posts posted by ryan-walks

    Cura update

    in UltiMaker Cura

    Posted

    Update:

    After sifting through dozens of hex and source files, with a little guess work, and a lot of research. I finally found firmware that will not only connect, but let me jog and heat up the extruder!

    Its the:

    http://firmware.ultimaker.com/firmware/UM-v1.1-PCB1.5-thermocouple-build-1-AtMega2560.hex'>http://firmware.ultimaker.com/firmware/UM-v1.1-PCB1.5-thermocouple-build-1-AtMega2560.hex'>http://firmware.ultimaker.com/firmware/UM-v1.1-PCB1.5-thermocouple-build-1-AtMega2560.hex'>http://firmware.ultimaker.com/firmware/UM-v1.1-PCB1.5-thermocouple-build-1-AtMega2560.hex

    at:

    http://firmware.ultimaker.com/firmware/

    Its looks to be some older stuff, but it seems to work on ReplacatorG0026.

    edit: It seems to be working with Cura as well.

     

    Cura update

    in UltiMaker Cura

    Posted

    An ISP (in system programmer) was designed by Atmel to let programmer handle non-usb compliant microcontrollers. They use a communication method known as SPI (Serial Peripheral Interface). They look like this:

    ispMKII.jpg

    They have headers like this:

    isp_6pin.jpg

    The Arduino Mega2560 has two of those headers, one for the bootload uC and one for the main uC. If you use the bootload uC to load code onto the main one (using the usb connection), your using the boot uC as an ISP (basically). Essentially its one more thing to go wrong IMO.

     

    Cura update

    in UltiMaker Cura

    Posted

    Also, out of curiosity, that the Electronics looks like a knockoff. Curious where you got it from. The Arduino also looks odd, as it does not say "Made in Italy" (something seen on all real Arduino's) So could be shady build quality electronics.

     

    I'm not %100 sure where the electronics came from, and the arduino says "designed in Italy" on the back.

     

    Cura update

    in UltiMaker Cura

    Posted

    Thanks for your help, this is defiantly useful information. So if its the wrong shield, is it possible that when I updated the firmware it burnt some of the ports? Is there any documentation of this older shield and possible compatible firmware to go along with it?

    This is the Arduino, so not the black one.

    thnu.jpg

     

    Cura update

    in UltiMaker Cura

    Posted

    The unit was working fine until the firmware upgrade.

    Are there steps for troubleshooting the shield? Or could it be the mega2560?

    If I used an ISP programmer to erase & reprogram the flash, could that work? I'm thinking it could be the USB boot loader chip on the board.

    edit: If anyone know what firmware the boards were running when ReplicatorG0024 was the most current software that would be perfect. That's when the printer was working last.

    edit edit: twpd.jpg

    Here is a picture of the shield, maybe this will help.

     

    Cura update

    in UltiMaker Cura

    Posted

    Hopefully daid will post again as I have never had any trouble in this area and don't understand it but I believe the default hex file is the one with the faster baud rate yet you installed the lower speed rate (although I thought it didn't matter). The log file looks EXACTLY like what I would expect with baud rate issues. Also with a broken USB, or arduino, lol.

    Anyway I would go to cura and go to "file" "preferences" and set the baud rate explicitly to whatever version of the firmware baud rate is.

     

    Thanks for your reply, I've when I go into device manager it won't let me set my baud rate to the 250k, so I installed "MarlinUltimaker-115200.hex" from the \firmware directory using the custom firmware loader on Cura. Still same problem.

     

    Cura update

    in UltiMaker Cura

    Posted

    Hey I just got an error log:

     


    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Send: M105 T0
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Send: M105 T0
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Send: M105 T0
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Send: M105 T0
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Send: M105 T0
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Send: M105 T0
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Send: M105 T0
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Recv: echo:Unknown command:""
    Recv: ok
    Send: M105 T0
    Serial timeout while writing to serial port, trying again.
    Unexpected error while writing serial port: SerialTimeoutException: 'Write timeout' @ machineCom.py:_sendCommand:506
    Changing monitoring state from 'Operational' to 'Error: SerialTimeoutExcepti...'
    Connection closed, closing down monitor

     

    Cura update

    in UltiMaker Cura

    Posted

    Where can I find the error log in the first run wizard?

    I've tried loading the code on the uC manually using avrdude and I get this:

    tkeo.jpg

    This is my problem in Cura:

    93ky.jpg

    The BAUD rate in my device manager should match the baud rate in cura right? Also where can I find old firmware, stuff that will work with ReplacatorG 24? If I can't get this to work I will just have to downgrade.

     

    Cura update

    in UltiMaker Cura

    Posted

    Hey guys,

    I recently started working with a Ultimaker printer and am trying to get it up and running. Before the printer was running using ReplicatorG, I install Cura and then updated the new firmware. Now its stopped working with ReplicatorG and Cura. When I run the checkup on Cura it just says "connecting to machine" and that disk spins around forever.

    If it hit skip checks, the next screen still fails at connecting to the machine.

    I have matched the BAUD rates and made sure the com ports are correct in device manager. I'm running win7 32bit.

     

×
×
  • Create New...