UltiMaker uses functional, analytical and tracking cookies. Tracking cookies enhance your experience on our website and may also collect your personal data outside of Ultimaker websites. If you agree with the use of tracking cookies, click “I agree, continue browsing”. You can withdraw your consent at any time. If you do not consent with the use of tracking cookies, click “Refuse”. You can find more information about cookies on our Privacy and Cookie Policy page.
I think I've short circuited the fan output of the fan at the print head. The fan does not behave as expected. E.g. a 24vdc fan turns on at full speed (M106 S255) but not at halve speedd (M106 S128). Where as this 24vdc works with a 12vdc power supply. So the part of the circuit it is about is from Arduino pin 7 (pin 8 at PCB connector, going to R20 of 1Kohm to Q4 (BD679 Transistor) to PWM terminal to where the fan can be connected.
I have the following set up to test it: Arduino Mega + PCB connected through USB cable to computer with a COM terminal to send GCODEs. I have a multimeter and oscilloscope at my disposal. When I connect the Arduino and open the COM I get some output of saying that temperature and what not gives errors (make sense as nothing is connected to the PCB). It says M999 to restart, so I send that code and it replies with OK. When I then send the GCODE to turn on the fan "M106 S[1-255]" like "M106 S128" for example I can measure a 5v PWM signal coming from Arduino pin 7 with a correct duty cycle. So the port is working. The voltage after R20 (1Kohm resistor), or at Base of Q4 is 1.28v.
Question 1:
From what I can see is that the fan is powered with the same voltage as the power supply (16-20Vdc). But the fan is 12v. So at full speed (M106 S255) the 12vdc fan need to take care of the 20vdc continuously? Is this correct? Or am I mistaken?
Question 2:
From what I know understand is that 5v is drops to 1.28 volt after 1KOhm resistance. Meaning that (5v-1.28v=)3.72v dropped on 1KOhm. Meaning that the Base of Q4 provides ((1000Ohm/3.72v)*1.28v=)344Ohm resistance. Seeing the datasheet of Q4 (BD679) I do not understand where this restistance of 344Ohm coming from. Is the voltage drop of 5v to 1.28v from PWM port 7 of Arduino to Base of Q4 Transistor normal?
Damaged electronics of print head cooling fan?
in UltiMaker 3D printers
Posted · Edited by Guest
Specs: Ultimaker Original with PCB 1.5.4.
I think I've short circuited the fan output of the fan at the print head. The fan does not behave as expected. E.g. a 24vdc fan turns on at full speed (M106 S255) but not at halve speedd (M106 S128). Where as this 24vdc works with a 12vdc power supply. So the part of the circuit it is about is from Arduino pin 7 (pin 8 at PCB connector, going to R20 of 1Kohm to Q4 (BD679 Transistor) to PWM terminal to where the fan can be connected.
I have the following set up to test it: Arduino Mega + PCB connected through USB cable to computer with a COM terminal to send GCODEs. I have a multimeter and oscilloscope at my disposal. When I connect the Arduino and open the COM I get some output of saying that temperature and what not gives errors (make sense as nothing is connected to the PCB). It says M999 to restart, so I send that code and it replies with OK. When I then send the GCODE to turn on the fan "M106 S[1-255]" like "M106 S128" for example I can measure a 5v PWM signal coming from Arduino pin 7 with a correct duty cycle. So the port is working. The voltage after R20 (1Kohm resistor), or at Base of Q4 is 1.28v.
Question 1:
From what I can see is that the fan is powered with the same voltage as the power supply (16-20Vdc). But the fan is 12v. So at full speed (M106 S255) the 12vdc fan need to take care of the 20vdc continuously? Is this correct? Or am I mistaken?
Question 2:
From what I know understand is that 5v is drops to 1.28 volt after 1KOhm resistance. Meaning that (5v-1.28v=)3.72v dropped on 1KOhm. Meaning that the Base of Q4 provides ((1000Ohm/3.72v)*1.28v=)344Ohm resistance. Seeing the datasheet of Q4 (BD679) I do not understand where this restistance of 344Ohm coming from. Is the voltage drop of 5v to 1.28v from PWM port 7 of Arduino to Base of Q4 Transistor normal?
Thank you.